GS1100-16 strange port behaviour

2»

Comments

  • Zyxel_Jason
    Zyxel_Jason Posts: 387
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Sales Associate 25 Answers First Comment
     Master Member
    Hi @RCTechCon ,

    Welcome to Zyxel Community!

    According to your description, I would like to check the following with you:
    1. You mentioned you use 20 of 24 ports on the Switch, may I assume your Switch is GS1100-24 or GS1100-24E?
    2. May you provide me the first 5 letters of the serial number? We would like to know the production year.(It should start with "S")
    3. May you share what devices are connected to your Switch? Do you also connect Unifi AC Lite like other users mentioned above? What is the application in your daily use? 
    4. Is there any new device or new application you use in the network recently? The reason I ask this is because you mentioned the Switch has been working well for a year.

    Thanks.

    Click this link to start: https://bit.ly/3R2Wx52
    Jason
  • Thor78
    Thor78 Posts: 4
    First Comment Friend Collector

    I have a similar problem with the GS1100-16. The port to which an AVM Repeater 1200 (firmware 7.50) is connected seems to hang up every few days. The LEDs are flashing, but the port is dead and won't work again until I've powered down the GS1100. I have already tested several ports and the problem moves with them.

  • Zyxel_Melen
    Zyxel_Melen Posts: 1,104
    Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate 100 Answers
     Zyxel Employee

    Hi @Thor78,

    Welcome to the Zyxel community!

    The LEDs are flashing, but the port is dead and won't work again

    This is likely due to a broadcast storm or loop since you mentioned the "LEDs" but not "LED".
    Could you share your topology for better clarification?
    Have you checked if other devices with the cable connection can ping each other when this happens?
    If you cannot ping each other means your network has a broadcast storm or loop. Finding out where the broadcast storm or loop comes from is a good start to solving this problem.


    Melen
  • Zyxel_Melen
    Zyxel_Melen Posts: 1,104
    Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate 100 Answers
     Zyxel Employee

    Hi @Thor78,

    Furthermore, you can also isolate the GS1100 with two PCs to verify whether it will stop working after a few days or not.

    If it won't, then this might be due to your network surrounding.


    Melen
  • Thor78
    Thor78 Posts: 4
    First Comment Friend Collector

    I didn't mean all LEDs. Only the LED of the affected port was meant. Only the one port to which the AVM Repeater 2400 is connected as an AP is affected. The other ports and devices continue to function and are pingable. I will deliver the network topology later.

  • Zyxel_Melen
    Zyxel_Melen Posts: 1,104
    Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate 100 Answers
     Zyxel Employee

    Hi @Thor78,

    Thanks for the more detailed information.

    Since you mentioned other devices are functioning, I would like to check the following with you:

    1. Try to ping the AVM Repeater 2400 when the issue happens.
    2. Replug the Repeater.
    3. Disconnect the AVM Repeater 2400 and connect another device to test that port's functionality.

    Thanks.


    Melen
  • Thor78
    Thor78 Posts: 4
    First Comment Friend Collector

    Topology

    PXL_20230317_105711313.jpg

  • Thor78
    Thor78 Posts: 4
    First Comment Friend Collector
    https://community.zyxel.com/en/discussion/comment/49810#Comment_49810

    I will report when the issue happens next time.

Categories

Switch Help Center

  • FAQ
  • New & Release
  • Video Tutorials
    • EnglishTiếng ViệtРусскийไทย中文（台灣）