-
Moved: How to configure port failure redundancy in Zyxel GS2210 24 Port Switch?
This discussion has been moved.
-
Suddenly can't use either of my Zyxel switches when connected to my home DSL router
I've been in contact with support for my TP-Link router because I have tried two different Zyxel switches which were both working before and have both stopped working now so I assume it was a problem with the TP-Link router, but they have said I should check with Zyxel as well, so here I am! I drew them this diagram to…
-
GS1200-8HP v2 loop detection
Hi,I got a brand new switch and when I plug it into a computer, it works just fine. But if I plug it to GS1920-24 or GS1900-24E, it complaints loop detected even when I have only these two connected to it. Is it broken? I can disable the loop detection but does not really make any sense to do it.
-
XGS1210-12 - 2.5G ports dropping intermittently
Hi! I recently got a XGS1210-12 for my home lab environment and have been using it to upgrade the bandwidth between my devices. One thing I've started to notice in the logs however are that both 2.5G ports seem to lose link simultaniously and get it back a few seconds later. This seems to occur about 2-3 times an hour and…
-
i have es1100-16 when i hook up to my wifi router it kills the wifi
router works but knockes out my wifi
-
GS1920 multiple VLAN's over 1 port
I have the following setup and I can't seem to get my guest AND private SSID's to work. i'm 100% sure it's on the switch. I know my port1 and port10 need to be configured in a way that both vlan's should go over them but the PVID in the PORT CONFIGURATION only allows 1 PVID. How would I let this topology to work?
-
[Solved] gs1200-8 management
Hi all, it's the first time I setup a managed switch and I'm having some headaches.1) I cannot upgrade the firmware. My device is running version V1.00 ABME.5 C0 and it refuses to upgrade complaining that GS1200-8_V2.00(ABME.0)C0.zip, downloaded many times from official site, is not the right one. I don't think this is…
-
SNMP or other solution for monitoring XGS1210-12 ?
Hi, I just acquired 2 XGS1210-12 switches. It's a very good product with a very good quality/price ratio, but it's a shame not to have any solution to monitor it. Apart from the web interface, it's not possible to use an external monitoring solution (nagios, zabbbix, prometheus...) to get information about the switch…
-
Looking for a Zyxel network expert available to contract to help fix a "broken" network
My company has deployed a network with approximately 10 switches and 23 access points with the help of a network expert who has been contracting with us. It is a complex deployment with multiple VLANs. I think we have reached the limit of this "expert's" expertise. We have most of the VLANs working but keep going back and…
-
GS1200-8HP v2 and Management VLAN
Hello. I've this problem, my management VLAN is 251 and VLAN 1 is not used. I cannot find the way to change the management VLAN from 1 to 251 on that switch. The firmware is update on latest version.
-
XS1920-12HP: loosing connectivity to devices in mgmt VLAN (except switch itself) after 5 minutes
Hi! I am experiencing a very strange problem in my network recently and I get more and more the impression it is related to the switch. I have a XS1930-12HP on which several VLANS are defined. One of these VLANs is the management VLAN where all the APs, AP controller, and switches of the network are connected. It looks…
-
Hi, I am using a ZYXEL PoE Switch, model GS1900-10HP, to test the power draw at a powered speaker.
Hi, I am using a ZYXEL PoE Switch, model GS1900-10HP, to test the power draw at a powered speaker. This switch does not support MIB for PoE information, so is there an alternative way of monitoring and accessing the consuming power data?
-
[Fixed] GS1200-8/8HPv2 management IP address issue
Dear Zyxel Users, We regret to announce an issue after upgrading firmware to V2.00 and would like to call your attention in the meantime. GS1200-8_V2.00(ABME.0)C0 GS1200-8HPv2_V2.00(ABMF.0)C0 The Symptom: The firmware listed above is subject to a bug which management IP address cannot be configured with 10.0.0.1/24, it…
-
How can I connect to a USB hard drive on ZyxelVMG3925 router?
Firstly - how do I log in to Admin on router? I see the ADmin password. What's the username?
-
replace SSL cert on management site
How can I upload a new SSL cert to place the untrusted one on the management https interface?
-
how to apply new firmware?
Feel like i'm missing something simple... I go to the maintenance -> firmware activity and upload the new firmware package. Wait a few minutes, log back in, and the new firmware package does not seem to be available. GS1900-24P
-
gs1900 24e
Hi i try to update to last firmware the switch but something goes wrong now the system is unreachable the unit attached goes well. What can i do fo recover the situation ??? the switch ip address result unreachable. I have checked the browser option and its all ok
-
GS1200-8 - Management VLAN (Firmware V1.00(ABME.4)C0)
Hello, In firmware V1.00(ABME.4)C0 for the GS1200 switch series there is a new feature implemented:* ... * Management VID is VLAN 1 only. According to the wording it seems the management VLAN is fix on VLAN 1 and this VLAN cannot be changed by the owner. While limiting management to a single VLAN is quite desireable, it is…
-
Trunk auf gs1910-24 GigaBit Ethernet Switch
Hallo Cummunity, habe den Switch schon seit 8 Jahren am laufen und erst jetzt das Update gemacht auf V2.00(AAAX.0)C0. Ich habe in meinem System mehrer andere Switche von Zyxel (neuer Varianten) in denen ich einfach den Trunk einstellen kann. Auf diesem hier finde ich die Einstellung nicht. Wo stelle ich den Trunk ein oder…
-
MAc address table empty... second time ...
I filled out the
Mac Address table with data from all PCs plugged into this device. I understood that
this table is fixed and does not disappear after turning off the GS1900-16. This table is
empty for the second time. Please, what am I
doing wrong? Thanks in
advance,
