Ace  Freshman Member

Comments

  • DNS is for resolved ip address usage if you were using ip address to access GS1900 then the problem should not relate to DNS server. I think your can access GS1900's web interface when your PC directly connected. But switch cannot be access when pc connects on other devices(e.g: tplink or wireless). Am I right? Maybe…
    in Zyxel GS-1900-24 connecting problem Comment by Ace August 2019
  • This description I found from help page: Enable VLAN Trunking on ports connected to other switches or routers to allow frames belonging to unknown VLAN groups to pass through the Switch. Did you create static vlan on XGS1930? If yes, did you add vlan member for R1/R2 these two ports?
    in XGS1930-28 vlan trunking support Comment by Ace August 2019
  • Yes!
    in VLAN Switch Uplink Comment by Ace April 2019
  • Yes, you can. But I don't think you need tagged out for VLAN 1, just tagged out for VLAN 10 should work. PC connect to phone and IP phones are connected to switch Port 1 to Port 9. Port 10 is uplink. All ports PVID are 1 and phone using voice vlan to transfer to VLAN 10. Below is my static vlan setting: VLAN 1: All ports…
    in VLAN Switch Uplink Comment by Ace April 2019
  • Hi jeremywatco Looks like you have created VLAN database of VLAN 10 on the switch and enable vlan trunking on the uplink/downlink ports of switches. Because VLAN trunking is using for traffic forwarding of unknown vlans. If you create VLAN database then vlan trunking port still refer to VLAN database setting. You may need…
    in VLAN Switch Uplink Comment by Ace April 2019
  • @cuong I'm confusing, your networking has ring topolgoy or not? If it is not and you just want to avoid looping issue. The MSTP is unnecessary. Just enable loop-guard on all ports excluding uplink port. When looping issue appear, you can go to ErrDisable or system log to find the detail information. BTW, by default…
    in MSTP not work Comment by Ace December 2018
  • @cuong No need enable MSTP on all ports. Your SW2 configuration is correct, because MSTP enable on (port 47)SW1 and (Port 48) SW3. Follow the same concept on the SW1 and SW3. It should work. For DHCP snooping, enable "dhcp snooping trust" on port if that port will receive DHCP server packets. SW1 needs enabled "dhcp…
    in MSTP not work Comment by Ace December 2018
  • Your SW1 and SW3 only enable MSTP on one port and those ports are connecting to SW2. If SW1 has connected to SW3 then those ports have to join MSTP as well. BTW, not sure you forgot to capture the full configuration for SW3, it should change to MSTP mode too.
    in MSTP not work Comment by Ace December 2018
  • Same issue report before. Looks like the problem relate to browser and firmware 2.30 or above version can solve the problem.You can refer the following link to check more detail. https://businessforum.zyxel.com/discussion/745/no-description-for-radio-buttons-on-gui-page-of-vlan-port-settings#latest I am not sure the…
    in I have a GS1900-24HP switch and in the management interface, most of the text does not appear... Comment by Ace November 2018
  • 我是網路維修工程師，服務的單位在台中。負責的Nebula Organization名稱是HS-Network。我喜歡Nebula的原因我不需要架設一堆伺服器收集資訊，同時我能夠監控好幾間宿舍，並且能夠讓我降低現場查修的次數!
    in [NEBULA] #SnapYourNebula拍下你的Nebula抽大獎活動現正開跑中! Comment by Ace November 2017
Default Avatar
EnglishTiếng ViệtРусскийไทย中文（台灣）