Zyxel_Derrick  Zyxel Employee

Hi @dan53 Since you have successfully uploaded the firmware to switch but it still can't be powered up. I think the switch may be broken and please find the local reseller for repairing it Thanks Best regards, Zyxel_Derrick

Hi @dan53 Welcome to Zyxel community Friendly remind that opening the chassis will break the warranty and it is not recommended to do it by yourself. Based on your description, please use XMODEM with 1K as the picture below and try to upload firmware again Thanks Best regards, Zyxel_Derrick

Hi @DocLove Welcome to Zyxel community Based on mac table and screenshot of your config on XGS1930, we think the configuration is correct. However, you have mentioned that you can't ping server that connected to port 49. Therefore, may I know where did you connect the PC to? what is the VLAN member of your PC and server?…

Hi @danyedinak It is common feature for switch to go back and forth the enable mode.That's why we keep it in the GS1900 series.I apologize for making you confuse and thanks for your advice.We will put it into the IDEAs to see if other users have the same idea.Thanks Best regards,Zyxel_Derrick

Hi @danyedinak Thanks for your informationGS1900 series is a smart managed switch which does not support CLI command to configure switch.From V2.50, we have enhanced the security that only the account with admin privilege can SSH switch.Therefore, the admin privilege account can switch back and forth enable mode without…

Hi @danyedinak Thanks for your feedback. About changing SNMP community string, we can see the same behavior as yours. Therefore, we will discuss with the internal about it. For the enable command in the SSH session, there is no such issue when I login as a user with admin privilege in my local lab. Therefore, could you…

Hi Webix Yes, you can put a range of VLANs on Allowed VLANs column Thanks Best regards, Zyxel_Derrick

Hi Eddie 我已經有在你的Po文做回覆 https://businessforum.zyxel.com/discussion/4262/gs2210-8hp%E7%9A%84poe-%E8%A8%AD%E5%82%99%E7%AE%A1%E7%90%86#latest 謝謝 Best regards, Zyxel_Derrick

Hi Eddie 你可以使用兩種方式進行斷電跟重新送電 1. Web GUI 登入switch的Web GUI後，到Basic Setting > PoE Setup > PD欄位進行設定 此部分可以參考使用手冊 P.76，可在下方連結下載 https://www.zyxel.com/tw/zh/support/download_landing/product/xgs2210_gs2210_series_22.shtml?c=tw&l=zh&pid=20140226133840&tab=User_s_Guide&pname=XGS2210/GS2210%20Series 2. CLI Configure > pwr interface…

Hi imaohw Yes, you can mix them in the same stack. To avoid stacking port being configured and cause the stacking mode unstable, users can't see the information on the stacking port. The only way to check if the transceiver works properly is to plug it in the normal port and do the cross test. Thanks for your…

Hi @Dudley_Winchester I have sent a PM message to you Please check the inbox Thanks Best regards, Zyxel_Derrick

Hi @Dudley_Winchester Based on your topology, we think configuring port isolation to all ports except for the uplink port can achieve your goal. For how to configure port isolation, you can refer to our handbook chapter 5.12. You can download it in the link below:…

Hi imaohw VLAN Assignment priority from high to low should be: Voice VLAN > MAC-based VLAN > Subnet-based VLAN > Protocol-based VLAN > Port-based VLAN > PVID Thanks Best regards, Zyxel_Derrick

補充說明一下 以上述提到的第一組config為例 classifier "snmp securityip" destination-socket 161 ipv6-source-ip 2001:288:0000::1 prefix-length 128 ipv6-next-header udp policy snmpsecurityip classifier "snmp securityip" egress-port 1 priority 0 dscp 0 tos 0 bndwidth 0 out-of-profile-dscp 0 forward-action forward outgoing-eport…

Hi KBWang 關於您提到的設定是屬於ACL的設定 一個classifier搭配一個policy rule等於一個ACL 以您的設定為例，從classifier name "snmp securityip"得知 classifier "snmp securityip" destination-socket 161 ipv6-source-ip 2001:288:0000::1 prefix-length 128 ipv6-next-header udp 是與 policy snmpsecurityip classifier "snmp securityip" egress-port 1 priority 0 dscp 0 tos 0…