Комментарии
-
After reset to default config i can access to device. After i restore config again - i can't access to device. And why device not permit ping? Router> show interface all No. Name Status IP Address Mask IP Assignment1 vpn1 Down 192.168.78.100 255.255.255.0 Static 2 vpn2 Down 10.0.0.78 255.255.255.0 Static 3 local 1000M/Full…
-
I think the issue in your engineers, that can't do its work good. I will update problem device on weekend to this patch. So you have a 1-2 week to did new FW and come up with an new idea.
-
I wrote, that i disabled FW via console port and it not helped🙉. ZW device can't ping other LAN devices with message ping: sendmsg: Operation not permitted What this mean? That you broke another time your devices with new FW?
-
Don't helped. S - Stability, that on any FW Zywall crashed
-
@Zyxel_Jeff After update ATP800 to P2, all usg1000 tunnels up. Later on this week try some times reboot device and watch result Don't up 2 FLEX50W tunnels. Flex on P2 FW too. In logs error about duplicate ip adress, that problem in this thread Send new diag and IKE syslog from both devices to PM.
-
Its very strange. Last error was at 8-20 [2023-06-05 08:20:09.776] unpack_message_rr fail ret=-31unpack_message_rr fail ret=-31 After that next message after 2,5 hours [2023-06-05 10:55:31.026] OCTEON eMMC stage 1 bootloader [2023-06-05 10:55:34.822] Success. [2023-06-05 10:55:34.822] Branching to stage 2 at:…
-
The ipsec don't work with ZW 1000 too, that don't affected to last buffer overflow issue. Sand diag info to PMРаздел: Ipsec via main GW stops work, Found old outbound SPI error in debug log Комментарий от alexey июня 2023
-
@Zyxel_Cooldia @Zyxel_Adam @Zyxel_Andrew @Zyxel_Bella @Zyxel_Chris punch your stupid devs Same issue on ATP800 with last patch. Device hang. After restart half ipsec vpn tunnels don't up. Debug log.Раздел: ZLD4.73 & ZLD5.36 patch 2 Official Version Released to address Buffer Overflow Issues Комментарий от alexey июня 2023
-
Send access to PM
-
Not help. I disable CC on ge2 & 3 interface show connectivity-check status Interface Status Fail Count cellular1 Ok 0 vti1 Ok 0 vti3 Failed 2 vti4 Ok 0 vti0 Ok 0 vti2 Ok 0 vti5 Ok 0 VTI interface, that build via this interface ge2 in failed status. Also change error message Possible ARP spoofing attack on IP 10.0.1.64.
-
My bad. I forgot that CC can be enabled on internal interfaces, and it status not displayed via show interface command. I disabled CC on interfaces and still wait new error messages.
-
We don't use Nebula features.
-
Symptoms: after long time ipsec stops working. Help only change Authentication method on both side. If it was certificate, than change on preshared key, or vice versa.Раздел: Ipsec via main GW stops work, Found old outbound SPI error in debug log Комментарий от alexey мая 2023
-
Welcome to "Dissappointed Zyxel customers club"🤝
-
The problem on same device and diff interface. Message from syslog server: src="0.0.0.0:0" dst="0.0.0.0:0" msg="An ip address conflict is detected. bc:99:11:a7:7e:d3 and bc:99:11:a7:7e:d0 share the same IP address 10.0.1.64" note="" user="unknown" devID="d8ece5c45727" cat="System" show interface all 1 ge1 Inactive 0.0.0.0…