Peter2

If it is VDSL then it is connected to VDSL plug of the Zycel . This would not be "fibre" . But the new Router has VDSL Modem capacity too , so plug the VDSL copper wire into the new Router . Leave the functioning ISP Router better as it is …

於 Zyxel DX 3301-T0 BRIDGE MODE 被 Peter2 評論 11月 11 日

I think when your ISP Router is connected over its WAN Port to the fiber modem , you only have to plug it out and into the combined LAN/WAN Port of your new Router and then configure .

於 Zyxel DX 3301-T0 BRIDGE MODE 被 Peter2 評論 11月 11 日

Yes, there is a fault on the regular site since some weeks ! This link is ok : https://www.zyxel.com/global/en/support/download?model=DX3301-T0

於 Unable to locate firmwares for DX3301-T0 被 Peter2 評論 11月 4 日

I think you can override DHCP and give a IP adress coupled on the MAC Adress of the IP tel . "static DHCP"

於 EX3301-TD - Voipfone connection issue (LLDP) 被 Peter2 評論 10月 29 日

So configure this IP phone with a fix local adress of your local net in the IP tel and in the Router . If it has an Adress you van configure it . When Problems try with deactivated sip.ALG in the NAT section . May be neccesary using other ports then the common Voip ports if you use paralel build in phone and IP phone .

於 EX3301-TD - Voipfone connection issue (LLDP) 被 Peter2 評論 10月 29 日

Hi, i think you should activate the logs for VoIP first . Shure there is a option for echo cancellation . May be you use a dect Telephone with its base on the analog Port ? This can result in echoes too some dect Tels have a special option against it .

於 EX5601-T1 VOIP issues 被 Peter2 評論 10月 23 日

1und1 often uses ds-lite for new accounts , then you dont have a real IPv4 Adress only one over CGNAT . Try IP V6 only if you obtain a IP V6 adress single. Try a Fritz box which ds lite capable if you have ds-lite . This device must be configured for ds-lite if thats true if it is even capable. You are here in the home…

於 ZyXEL SBG3500-N000 configuration for VDSL via 1&1 被 Peter2 評論 10月 17 日

You should post a picture of the menu Network/setting/broadband to configure There you configure "VDSL over PTM" - deactivate over ATM "Routing " "PPPOE" activate Vlan p=0 q=7 MTU 1492 In PPOE you have to put in PPP username like this 1und1/+++++++@online.de get your adresses automatic The device is old , but seems to be…

於 ZyXEL SBG3500-N000 configuration for VDSL via 1&1 被 Peter2 評論 10月 16 日

You want to login to the UI for firmware upgrade via internal ftp of the device ?

於 TFTP setup for netboot.xyz 被 Peter2 評論 10月 11 日

Of course this is your decision … One thing at last - may be its better to give the new interface on Lan4 really a adress in your primary lan like 192.168.1.252 and the modem adress change to 192.168.100.1 which is a standard bridge modem adress very often . Then connect the modem Lanport to Wan port of the router and the…

於 VMG devices bridge mode not accessible via it's management IP 被 Peter2 評論 10月 9 日

You can test it with a laptop connected to the running Modem on another Lan Port if it works both : access with the same adress of the Modem oder access over Lan4 with your new interface . Then you have to configure your synology right to get access over your Network .