Best Of
Re: Expand PLA6457 Network
Hi,
have you read my post? Did I mention page 13 there?
Guys, RTFM does not help. I might misreading stuff there. In this case it will help to point me to the correct steps. It does not help telling me "read it again. And again.....".
Citing page 12:
You can connect a number of PLAs on a G.hn Network, but you can use the ENCRYPT button on only two PLAs at a time.
So from my understanding I can add multiple devices to the existing network of two PLAs.
I did the 5 steps mentioned on page 13 but as written the connection to PLA-B gets lost.
/KNEBB
knebb
1
Re: Services Activated but I did not Activate them!
All my other USG services never got activated so not sure why they got activated unless its a new thing that they activate without you knowing now?
PeterUK
1
Re: Zyxel ax7501-b0 guest wifi problem
mMontana, yet didn't asked to ISP because wanted first understand if I'm doing something wrong in the settings.
tonygibbs16 tnx for the links, will read it better, but the Iphone 12 sees the 2.4 GHz guest network SSID and connects to it, just soon later comes the "no internet connections" warning under it. this when with same wifi is used with internet connection by the iphone 7. already tried to remove it and add it again or restarting also the 12 but not working yet.
and the other two regular wifi (2.4 and 5GHz) are successfully used with the Iphone 12, just the guest isn't.
for this I'm asking here
tonygibbs16 tnx for the links, will read it better, but the Iphone 12 sees the 2.4 GHz guest network SSID and connects to it, just soon later comes the "no internet connections" warning under it. this when with same wifi is used with internet connection by the iphone 7. already tried to remove it and add it again or restarting also the 12 but not working yet.
and the other two regular wifi (2.4 and 5GHz) are successfully used with the Iphone 12, just the guest isn't.
for this I'm asking here
Chris_V
1
Re: AMG1302-T11C - Username character set
Hi there
The system might not allow to use some special characters for avoiding attacks, it might be the reason you can't use "^".
On the other hand, this model is an old model and I believe it has EOL many years ago, there would no firmware enhancement anymore.
FYI
The system might not allow to use some special characters for avoiding attacks, it might be the reason you can't use "^".
On the other hand, this model is an old model and I believe it has EOL many years ago, there would no firmware enhancement anymore.
FYI
SEJ
1
Re: Future Application Support
Hi @odifoke
Thanks for your feedback.
The Zyxel server will not stop the service for at least three years and this service is considered as our long term service.
Re: HTTPS virtual server - requests coming in on different ports?
SOLVED!
Ok, the port number thing was throwing me off. I looked at a different port forwarding that is working and the random ports are in the logs there too. So, that was a red herring.
The problem was I had To:LAN1 on an ATP500. I don't use many of these. I use a lot of the ATP100/200s. These have LAN1 predefined. On the ATP500 there are no default members in LAN1. However, LAN has the member physical ports of my LAN. Once I changed the Policy Control rule To:LAN it all worked.
Thanks,
-John
Ok, the port number thing was throwing me off. I looked at a different port forwarding that is working and the random ports are in the logs there too. So, that was a red herring.
The problem was I had To:LAN1 on an ATP500. I don't use many of these. I use a lot of the ATP100/200s. These have LAN1 predefined. On the ATP500 there are no default members in LAN1. However, LAN has the member physical ports of my LAN. Once I changed the Policy Control rule To:LAN it all worked.
Thanks,
-John
Re: NR7101
Hi Tony,
Thanks for your reply.
I have already tested with everything on auto. It did not make a real difference.
Is it possible that the router has a hardware problem? I think it has several antennas inside. What if one or more are not working properly? Is there a way to test that? The router arrived in a box that was slightly damaged. I guess it got dropped during transport. The major speed difference compared to my mobile phone could be explained by an antenna not receiving a proper signal.
Do you know a way to see which bands are used on an android phone? This ways I can compare the bands used by the router vs those on the phone.
Another thing that I can try is to downgrade the LTE module firmware to the previous version. Apparently there are some users that said that the latest version actually caused connection and speed problems.
Thanks,
Peter
Thanks for your reply.
I have already tested with everything on auto. It did not make a real difference.
Is it possible that the router has a hardware problem? I think it has several antennas inside. What if one or more are not working properly? Is there a way to test that? The router arrived in a box that was slightly damaged. I guess it got dropped during transport. The major speed difference compared to my mobile phone could be explained by an antenna not receiving a proper signal.
Do you know a way to see which bands are used on an android phone? This ways I can compare the bands used by the router vs those on the phone.
Another thing that I can try is to downgrade the LTE module firmware to the previous version. Apparently there are some users that said that the latest version actually caused connection and speed problems.
Thanks,
Peter
Re: NR2101 IP Pass-through
Good morning @martiko
Yes, I have some good news. I got an update from the Zyxel support that solved the issue for me.
The way NR2101 works is that it will bind the first device that connects after setting IP Pass-through in the settings UI. The binding seems permanent, even if you disable pass-through and enable it.
What solved the issue for me was to factory reset the device. Connect the client I wanted pass-through to work for, and with that client enable pass-through in the UI.
I hope this helps!
/A
Yes, I have some good news. I got an update from the Zyxel support that solved the issue for me.
The way NR2101 works is that it will bind the first device that connects after setting IP Pass-through in the settings UI. The binding seems permanent, even if you disable pass-through and enable it.
What solved the issue for me was to factory reset the device. Connect the client I wanted pass-through to work for, and with that client enable pass-through in the UI.
I hope this helps!
/A
Brackan
1