-
How to mange the output power of USG LITE 60AX?
Navigate to Site-wide > Configure > Security router > Radio settings Scroll to the bottom of the page, select the model, and click "Edit" You can manage the maximum output power on this page. Note: SCR 50AXE does not support to mange output power
-
How can I manage USG LITE 60AX without Nebula?
USG LITE 60AX does not support standalone mode. The local GUI includes WAN configuration options. Additionally, here are some debugging tools for troubleshooting internet issues If you would like to configure your WAN settings directly without using Nebula, the following link provides steps to access the local web GUI.…
-
Security Router Matrix Table
Category SCR 50AXE USG LITE 60AX Rule / Policy Limits VLAN 4 4 Firewall Rules 15 15 Virtual Server 10 10 Application Profile 5 5 Application Bandwidth Control None 10 Application Bandwidth Control by Usage None 30 Content Filter Profile 5 5 Custom Allow Domain 50 50 Custom Block Domain 50 50 Site-to-Site VPN 3 3 DNS…
-
[ATP/FLEX] What is the maximum number of Static DHCP table supported on Nebula firewall?
Question: What is the maximum number of Static DHCP table supported on Nebula firewall? Answer: Nebula mode USG FLEX 100 60 USG FLEX 100W 60 USG FLEX 200 150 USG FLEX 500 300 USG FLEX 700 450 ATP100 60 ATP100W 60 ATP200 150 ATP500 300 ATP700 450 ATP800 450
-
How could I reserve IP address for wifi clients on USG LITE60AX on Nebula?
Here are the steps to set up static IP for the devices 1.Go to the section Site-wide - Clients 2. Select "Client list" 3. Choose the category as "Secuity router clients" 4. Select a client which is connected to SCR device and click "Policy" and select "Reserve IP" Or you can click Add Client to set up the static IP address…
-
How to enable/disable the threat management on security router SCR50AXE/ USG LITE 60AX?
Navigate to Site-wide > Configure > Security router > Threat management You can verify which threat management features are enabled or disabled.
-
Why Security router SCR 50AXE cannot boot up?
If your security router doesn't boot up, please follow these verification steps: 1.Ensure the power adapter is properly connected and functioning. Try different power outlets if the issue persists. 2.Unplug all Ethernet cables and check if the device can boot up without any cables connected. 3.If the device does not boot…
-
Will the prevention features still be active after Elite Pack license expire?
The threat management function will continue to operate even after the license has stopped or expired. To verify if threat management is still active, attempt to access the domain ' www.goooooooooooooooooooooooooooooooooooooooooooooooooooooooooogle.com' If the website is inaccessible and event logs appear on the Nebula…
-
How to reset security router USG LITE 60AX?
To reset the Security router, press and hold the reset button for at least 8 seconds. For more information, please refer to the User Guide as link below https://download.zyxel.com/USG_LITE_60AX/user_guide/USG%20LITE%2060AX_V2.00_Ed5.pdf
-
How to reboot the security router through Nebula?
You can go to Site-wide > Monitor > Devices > Security router > Click reboot the device on the Nebula Note: It is not possible to reboot the device when security router show disconnected from Nebula.
-
How to turn off the power on security router?
You can turn off the security router by unplugging the power cable. Note: It is not possible to turn off the security router through Nebula.
-
How to check Elite Pack license status on Nebula?
Navigate to Organization-wide >License &inventory >Licenses You can view your license details status on the page.
-
Do I need the Nebula Pro pack if I have already purchased the Elite pack?
The Elite Pack License is available for the USG LITE 60AX and SCR 50AXE hardware models. If you have already purchased the Elite Pack, you don't need to buy the Nebula Pro pack for your security router. The Elite Pack includes the Nebula Pro pack. For more information, please refer to the link below:…
-
How to set up WAN setting for USG LITE 60AX?
To config USG LITE 60AX WAN settings, you can go to Nebula. Navigate to Site-wide > Configure >Security router > Interface Click the edit icon on the right You can select the WAN type under the Interface properties
-
How to turn off Wi-Fi on model SCR 50AXE
Navigate to Configure >Security Router > SSID settings Disable the enabled button, then the Wi-Fi on SCR 50AXE will be disabled.
-
If I select a wrong license in a shopping cart, how to cancel it?
To cancel the selected license, you can go to shopping cart and click the remove icon on the right of the field. If you have more questions about purchasing a license, you can contact us
-
Does the Elite Pack license can assign to the firewall series?
The Elite Pack License is available for the USG LITE 60AX and SCR 50AXE hardware models. For more information, please refer to the link below: https://www.zyxel.com/global/en/elite-pack
-
What is the LED light status on USG LITE 60AX?
The following are the LED status of USG LITE 60AX For more information, you can refer to the User Guide What is the LED status when blinking between from amber and green on the USG LLITE 60AX? Fast Blinking between amber and green ( 300 milliseconds interval): The Zyxel Device is booting up Slow blinking between amber and…
-
What should I do if my USG LITE 60AX is not connecting to Nebula?
Check your internet connection: Log in web GUI and check the wan settings, you can refer to the following link below how to check if the WAN connection for USG LITE 60AX? Verify the device connection: Make sure the USG LITE 60AX is powered on and correctly connected to your network. Reboot your devices: If the issue…
-
How to check WAN connection for USG LITE 60AX?
To access the local web GUI, connect an Ethernet cable directly to one of the LAN ports (1-5), then open a web browser and enter the default IP address: https://192.168.168.1 After logging in, go to Configuration > Network > WAN Settings, then click on Connection Test to check if the connection is active.