Triu  Freshman Member

Comments

  • Don't think about it anymore. It costs me and you alot of time and after i switched back to my workdesk, i put in the power cable and it turned on without the power button. I tried to shut it down with the power button and it worked, but disconnect the cable and connect it again, turned it on immediately. What should i…
  • Tried different Ports (on Router and NAS) and another cable, but with the same result. Can't measure the voltage. Unfortunately the NAS520 has a 12V power supply so i can't try this out.Think i do the TFTP and uImage stuff again.Edit: When i change IP and then directly connect to the webinterface it works, but again with…
  • The output you have requested: When i change it with "ifconfig egiga0 192.168.178.31 netmask 255.255.255.0" it will be overwritten after some seconds (after: network_common.py.pre), see here:
  • Nothing special happened, you got it running, i played a little bit with it's settings, then it was off most of the time. Then i've done the factory reset (with 3 beeps) and now it isn't working. :/ My browser deletes everything, everytime i close it and i tried to connect through IP (not through URL or Name). I bought…
  • Thank you alot for your detailed steps. So i've done a regular boot without interaction, till i can write to the console, here the attached LOG starts. Then i used your commands and they worked. At the end i didn't know how to boot from it. The boot commands didn't work so i rebooted it completely and then i ended with the…
  • So, i am not exactly shure what i have to do. Should i make a seperate NANDPATH? Or skip this, cause i will use the existing?MNT_POINT i can choose one?How to give him the ubi${IMG_MTD}? => ubi${dev/sda1/sysdisk.img.gz.520ABAG1C0} ?Or do i only need the last mount line? Sorry, i am really not used to this kind of stuff.
  • I've found that command, too.This changes my console to this sign in the front '>' and nothing is in there.No command works and 'ls' gives nothing.
  • Great to turn off the buzzer.But can't copy to destination, cause read only.cp: can't create '/firmware/mnt/nand/sysdisk.img.gz.520ABAG1C0': Read-only file system<br>
  • The kernel is still valid? Hmmm. The changed start parameters from the past can't disturb this?He is still loading it, cause i didn't make me a copy to set it back. For the USB stick, i think i can. I see it with "lsusb" and i know i can create a folder. The "mount" command is also there. What should i put on the stick?Is…
  • Hello Mijzelf,thank you for helping again.I didn't use it alot the last weeks, but a regular start was no problem.I played a little bit with all settings, cause of the Debian which was installed before,i don't know everything on stock Zyxel NAS.That was the reason i wanted to reset it. Attached is the log when doing…
  • Unfortunately....i pushed the reset button to do a factory reset (3 beeps). After that it didn't come up, only the anoying beeber which doesn't stop. I connected with serial again and saw that it has problems with a corrupt NAND Flash.So i tried to do the same as before, loaded the uImage.520ABAG1C0.bin but with the same…
  • Found it on youtube, commented by Zyxel in the third answer: https://www.youtube.com/watch?v=O--SPdrQu68 Also the power supply seems to be different. On my 542 it is 19V, on 540 it should be 12V, found here: http://naschart.com/compare/zyxel-nas540-nas540-151,zyxel-nas542-nas542-149 But anyhow, as long as the firmware has…
  • Yes, found out that the main reason is 540 is for America and 542 for the European market. 540 came out 2015 and the other one year after, but don't think Zyxel will drop support for that one earlier than the other, cause as you mentioned, they are the same. Tried to get a 542 firmware on it but now it is refused. So i…
  • That did the trick. Firmware upgraded to V5.21(AATB.1)C0, now i do a second upgrade online to V5.21(AATB.2)C0.That worked too, great, seems everything is working now, only the model name has changed from NAS542 to NAS540. Found on your FTP a folder for NAS542 with 520ABAG1C0.bin inside. Is that the original firmware for a…
  • Not on the first try, there was a loop again, so i made another reset and the loop was broken, i set the IP and could login with admin. Now i have the control center :) Going to the firmware update tool, it tells me not the actual version (it's empty), but it is saying i'm up to date. :s Should i do a manual firmware…
Avatar