Best Of

Re: USG FLEX 50W Not Following Allow Policy

I ended up removing the rule completely and rebuilding it again. It is now working.

However, I found another rule that is for management access to the PBX that is also blocking the packets. On this one, I changed the service object from a specific port on the external side to match with the same port on the LAN1 side (device) and it works. This required changing both the policy and the NAT rule. So, there appears to be a problem with this particular static NAT rule for some reason.

I put the original external port back in to both the security policy and the NAT rule and it is blocking me once again. ?????!!!!

DeanH

1

Re: USG FLEX 50W Not Following Allow Policy

Finally figured it out. I forgot that on the security policy, it wants to see the LAN1 port, not the WAN port as the Service. That is so confusing since I am used to a WAN rule utilizing WAN components (IP/ports), not LAN components (IP/ports).

DeanH

1

Re: USG FLEX 50W Not Following Allow Policy

Rule of thumb about security policy rules.

98% of the times the author write it wrong. I did that too, so many times

mMontana

1

Re: Which Wan IP ? Lete7490-M904

JMB_74 said:

So now, which ip using to access the router from internet ?

Currently none. Ask your ISP/Provider for more info about direct access to your device or your "own" public IP.

mMontana

1

Re: 1920-8HPv2 - SYS LED flashing rapidly. System does not boot

Dear @Moritz_M , The stable/latest firmware of GS1920-8HPv2 had already released for some time, but there is no similar feedback from other users recently, so we hope you may help us to confirm the points below: The SYS LED flashing means the device is booting up, could you let us know how long have you waited? Over 1 minute?There is a Reset button which will reboot Switch with cold start and also a Restore button to reset the Switch to factory default setting when holding for over 7 seconds.On the right-hand side of the Switch, there is a 4-pin port can be connected with a 4-pin-to-USB console cable, do you have the cable?If you have "waited for a long time", "tried to reset or restore", "don't have such console cable on your hand", we recommend you contacting your reseller for the RMA process.

Zyxel_Ivan

1

NBG7815 Port 80 and forwarding

I bought a NBG7815 router for the 10gb port yesterday. However I can't forward Port 80. I run my own server and cloud which needs that port. I was also displeased at having to set up an account to use a device I bought that generally does not need an account. What happens if Zyxel stop trading? Do I end up with a brick (useless device)?

Issue 1 is port 80. You need to change this. It is not acceptable in this day an age for a router to disallow the forwarding of port 80. You have plenty of other ports open which can use for use for your cloud account stuff.

Issue 2. After setting up the router I now get a "service unavailable" message so can't even log into it. I don't want to have to go about resetting it for the second time. The first was because it decided to not work after I changed the IP address and connected it to my modem.

If anyone in the community can help or offer advice on the above it would be appreciated.

As for Zyxel I now have three options. 1. I can wait for OpenWrt who are currently working on it, 2. I can root it and try to forward the port myself or 3. I return the device as not fit for purpose as I am within the return timescale. At the moment I am looking at 3. So please tell me your intentions with fixing this so I can make an informed choice. You have to understand if someone is buying your router then they generally have an internet connection over the standard 1gb and there is usually a good reason for that. Sure some use it for gaming but I would say that a very large percentage are paying for the extra bandwidth for the exact same reason as me.

I await a response in this matter. As I said if anyone in the community has any ideas on my problems that would brilliant, thanks.