-
Is there a location to download firmware for ES-3124
Just looking for a location where I can find it.
-
Jumbo-Frames on GS1200-5/8?
Hi, my GS1200-5 has the latest firmware installed. According to marketing speech it can deal with Jumbo Frame. Unfortunately I do not see any options to enable it. And it looks like it does not offer Jumbo frames. My QNAP NAS is connected to a QNAP switch (both Jumbo Frames enabled) and the GS1200-5 is connected to the…
-
Info about XGS1250-12 with SFP+ RJ-45 Copper Transceiver
So there was a deal on the XGS1250 on amazon and for down the road upgrades to my network rig I might as will get one now in the end the SFP port will be used without the SFP+ RJ-45 Copper Transceiver but for the time being I had one and it works fine on my XS1930-10 but at first would not work in the XGS1250-12.…
-
XS1930 default-gateway per each VLAN- Do I need L3 Access license?
I am moving my configuration to multi vlan and I would like to add a default gateway per VLAN. e.g. vlan 1 comes with the default gateway in the web based configuration. I created vlan12 and I would like to assign its own default gateway but I do not see how to do it and in the show run I can see the default-gateway for…
-
Zyxel XMG1915-10E LEDs?
Does this Switch have the option to turn these off? if not, are there any LED's inside the ports or only on the left side where they are grouped toghether? Planning to put this in the room where i watch movies in near pitch black, if there arent any LED's in the ports themselves i can just use some LED dim foil to cover…
-
XGS1250-12 not linking at 10G or any speed / port
I have 2 systems (win11) and I am using ASUS XG-C100C NIC. Neither NIC will establish link with the switch. I have tried auto negotiate, forcing both sides the 10G. No success. If I set the card to auto and plug into a 1G port, same results. NIC supports 1,2.5,5,10G. I have tried several cables Cat6, 7' long. If I use the…
-
XMG1915-10EP Cannot Set Static IP
After trying to set a static IP for the switch (System → IP Setup), save the configuration, and then reboot, the switch will stop functioning and force me to a factory reset. This switch will only become non-functional after reboot. After setting the static IP, everything will still work as before. However, reboot will…
-
XS1930-10 New Firmware Problem 4.80(ABQE.4)C0
I just upgraded the firmware on 2 XS1930-10 switches to 4.80(ABQE.4)C0 and noticed high and constantly high CPU utilization for my configuration. CPU steady above 36%. My switches only have 3x 10 gbps connection and 1x 2.5 gbps and the other one has a 2x LAG 10gbps to a NAS, 2x10 gbps to a computer and AP. I reverted the…
-
Firmwareupdate Zyxel GS1900-24E B1 from 2.8 to 2.9
I tried to update the firmware of my Zyxel GS1900-24E B1 from version 2.8 to 2.9. I used, Chrome, Edge, Firefox and ZON. However it always fails to update.
-
[XMG1915-10EP] CLI Command List
Hey, is there an overview of the CLI commands for the switch XMG1915 Where can I find them? thenk you
-
[XMG1915] rx/tx issue between client and up-link
Issue: *Cannot ping from any direction client ←→pfsense.*no automatic ip from my pfsense dhcp. steps: *factory restored switch *changed its static ip (192.168.0.11) *turned of that cloud thingy *used the vlan helper tool: (port16 is up-link pfSense connected) On port 10, i have some eth dongle confed as follows: Ethernet…
-
what is the relation between RSTP and Bridge Control Protocol Transparency feature
on my XS3800-28 i have enabled RSTP on all ports but do i have to enabled Bridge Control Protocol Transparency feature as well in order for RSTP to function properly? I have no loops and RSTP seems to operate just fine but read that BCPT should be enabled if STP is in use. XS3800 serves as core (root bridge) and then i…
-
Strange log message. Is this an error?
Hi Anyone that knows what this means? I have not seen any link up/down. Happened 9 days ago on one port. And yesterday on two ports. Hardware fail? The switch is just 2 weeks old. 2 2024-12-09T23:12:28Z NO system: PethPse Port 7 - Axis-garage-2 OnOff Trap Port Detection Status is Delivering Power 3 2024-12-09T23:12:28Z NO…
-
GS1920-24 cant boot up, cant restore to factory
Hi, i have a GS1920-24 which start blink sys led when i powered it, during start up all port led is up in red and green then off. After about 1 minute sys led turn off, and nothing work. i tried press and hold reset button at side but nothing happend. Here is picture of board and video of startup progress:…
-
Fritzbox 7590 restart and probably negotiation problem
Hi everyone, I have a zyxel GS1900-24E to which I connected a fritzbox 7590. on both devices I have the latest firmware versions. When I restart the fritzbox, very often I encounter problems, for example continuously pinging the dns of google (8.8.8.8) I have many time out and the connection sucks. Doing a test with speed…
-
Media type DAC10G not displayed properly
Hello everyone, when you set DAC10G on a specific port: It is not displayed properly when you enter the port details: on "Status" you see SFP+ while it should be better to see DAC10G, as declared in the settings page. Is it possible to see that info? You have the same problem with LACP links: if you declare DAC10G on the…
-
Possible bug in Zyxel XMG1915-18EP
When setting System→IPv6→IPv6 Addressing→IPv6 Default Gateway I cannot use a ULA (I get an error about the address) or an LLA. It accepts the LLA address in the UI for IPv^ Default Gateway, but it ends up corrupt (discovered via the console with show ipv6 route). Only a factory reset and cold boot would recover it.
-
I would like to get visio stentles for zyxel switchs
I would like to get visio stentles for GS series. Specifically GS1900-24HP and XGS2210-28hp
-
XMG1915-18EP 10gb copper SFP+ shop
Hi, I am really struggling to find a supplier of 10Gb SFP+ modules for the XMG1915-18EP switch. I have tried Mikrotik and 10G GTek 80m modules but I get weird ddmi errors stating things like infinite low rx and tx reading intermittently causing the link to flap up and down constantly. These modules even when relatively…
-
XMG1915-18EP Passive PoE?
Hi, I need to power an edge switch that can use passive PoE as its power source, can the XMG1915-18EP support passive PoE? I would like to avoid using a PoE injector but if the XMG1915-18EP does not support passive PoE can it be added if it is not a feature available today? Alternatively I may just be missing something in…
