-
Cannot upgrade to v1.30 on USG Flex 200H. What's causing this?
Hello there! I am looking to upgrade to firmware version v1.30 on the USG Flex 200H because I am experiencing and issue where the device randomly reboots. I have tried to look through the system logs to for a trace of the issue but can't seem to find any logs pertaining to the issue. In the meantime, I was looking to…
-
v.130 for Flex 500H?
Are there no v1.30 release for Flex 500H?
-
USG200H rebooted itself, Netconf RPC errors
Hi After about 80 days of continuous operation, the device rebooted itself. Before and after this reboot, the following errors are shown: I have noticed other problems with this device: long lists (DHCP IP, NAT, Log, Security Policy) are super slow. the interface was better and faster in previous models (e.g. Flex 200,…
-
Updating to V1.30 if on ITS
So for anyone seeing this you have to be on V1.21 non ITS so you have to run a slot with this if you don't have a slot with V1.21 which I did but likely you have to do this which is update by Nebula which will only install V1.21 on your standby slot then on the UI of the Flex H can you upgrade to V1.30
-
EBL USG FLEX - whether it works properly
Hello, EBL in the H series has a problem with long txt files, I received new firmware, I'm testing it and I'm wondering if EBL should really work like that. After connecting the list, I hoped that the IP addresses from the list would be blocked similarly to security rules, and it works as follows: it passes the address…
-
On boot up bridge traffic being allowed without control policy
USG FLEX 200HV1.21(ABWV.0)ITS-24WK35-0813-240800592 So on boot up bridge traffic is fully allowed before control policy gets applied some seconds later about 1 minute and 40 seconds later…
-
200H: Device Registration Status: Not Registered
Last few days this happens a lot.
-
Update on DDNS not working
V1.21(ABWV.0)ITS-24WK35-m5760 DDNS does not work as it wants to ARP for the IP of the DDNS service this needs to be changed so it uses the interface gateway along with no need to ARP for DNS too. Cisco is my ISP gateway
-
Login to VPN with Google 2FA
Hi! I have a Zyxel USG FLEX 200H firewall, with Firmware version: V1.21(ABWV.0), release date: 2024-07-11 06:36:08. I would like my users to be able to use the VPN from the firewall with 2FA on connection, like Google Authentication. Is it possible to setup with only the GUI of USG FLEX 200H, or do I need SecuExtender or…
-
DNS and site to site Policy-based Zywall replies
USG FLEX 200H V1.21(ABWV.0)ITS-24WK35-0813-240800592 So here is a quick show of the problem with Policy-based site to site with DNS FLEX200H local 192.168.138.0/28 remote 192.168.144.0/24 USG40 192.168.144.0/24 >192.168.255.243 > FLEX200H 192.168.255.235 > 192.168.138.2 When a IP from 192.168.144.0/24 send dns to…
-
AD Server Authentication fail on the USG Flex 500H if domain name start with a number
ZYXEL usg Flex 500H Firmware V1.21(ABZH.0) | 2024-07-11 06:36:27 i try to join my domain in user authentication / aaa server / ad server summary. Configuration validation check passed with ok but when i try to join AD Domain i can't because my domain name start with a number (!?!?!) my domain is perfectly working and i…
-
Multiple VLAN on single port for Flex 700H
Hi, Does Flex 700H support multiple VLAN on single port? I want to have the default VLAN1 and some other VLANs running on the same port connected to another switch from Flex 700H According to the manual, it say "You cannot configure a VLAN interface and an Ethernet interface on the same port".
-
Admin interface protected by OTP not working after few hours/days
Hi, I have activate Two-factor Authentication for Admin access on my Flex200H (firmware v1.21(ABWV.0). It's working fine, but after few hours or days, when I connect OTP was not asked. If I disable/enable admin Access, OTP was asked again but for few times… This problem exist in previous firmware too. Best regards Luc
-
200H Not possible to disable, edit or remove default global zone forwarder.
200H - firmware 1.21 Why is it not possible to disable, edit or remove default global zone forwarder? System→DNS & DDNS→Global Zone Forwarder
-
USG FLEX 50 (USG20-VPN)
Hello, after resetting the USG, impossible to connect it with IP 192.168.1.1 ping no answer, with Wireshark I see no traffic on the IP 192.168.1.1 Power and SYS leds are green and stable, P2 led is orange and blinking My router DHCP give 192.168.1.1 to the USG, P2 is WAN .. so, I don't know what to do.. I tried with…
-
USG FLEX 200H - URL THREAT FILTER - justid.io
Firewall reports in the threat filter the URL Phishing justid.io to two target addresses 3.225.57.215 3.229.62.193 computers scanned with the best antivirus programs did not detect anything, only WireShark actually shows connection attempts to these addresses. How to solve the problem.
-
new release and HA support
hello when is it supposed to have a new firmware release, enhancing the configuration interface (now very poor compared to the USG/ATP series) and supporting HA as well ? regards Paolo
-
VPN SSL
Can I configure only one SSL VPN access policy on this H FLEX series?
-
VLAN ID on external interface PPPoE - Flex 100H
Does anyone know how to set a VLAN ID on a PPPoE interface type?
-
Why did you do this to virtual interface
USG FLEX 200H V1.21(ABWV.0)ITS-24WK35-0813-240800592 So back when I was testing before V1.2 it was fine I could do: 0 running config# vrf main interface ethernet ge2 ipv4 address 192.168.254.1/29 0 running config#! Commit but now you added this ERROR: [LY] / vrf main interface ethernet ge2 ipv4: Must condition…