Pbee  Freshman Member

Hi @Zyxel_Judy here a small update on the previous comment. I've been very busy and haven't had time for a long debugging session yet. But I think I've found why the country tag kept showing "US" instead of "NL" in MacOS on some Mac's: it appears to be a hardware thing in these Mac's. Apparently in some Mac's the wifi chip…

Hi @Zyxel_Judy here some quick responses: Our WAX650S devices are running in Stand-alone mode on separate network segments. The country code shown on our Mac's is indeed "US". This may not be a problem unless it violates HF regulations. I need to investigate this on more machines though. The connection rates I mentioned…

Two issues I found: For some reason our notebooks show that our WAX650S is broadcasting country code "US" instead of the default setting "NL" in the conf file. "Default country-code NL" And even more strange, when entering the CLI: Router# show wlan country-code Default Country Code : ED This issue didn't exist before…

@edvhoerstelde I would opt for the WAX650S. My experience is that it has a great coverage, good balancing the bandwidth over all mobile devices and quite resilient to neighbouring wifi and other HF disturbances. The "smart antenna" does really work. We use them in standalone mode. The Wifi 6E option sounds nice, but it…

Has this version been revoked? Can't find the WAX650S version anywhere in the download pages.

Hi, At this moment the WAX650S unit is in stand-alone mode for this network. It is connected to a GS1920-24HPv2. There was not much difference noticeable when the "multicast to unicast" option was enabled before I did that last test. But I'll try the 12Mbps option later this week. Until then. Thank you.

Those settings are already in effect. DCS is off and DFS is off (as far as regulations allow). On 2.4GHz its limited to 20MHz due to the fact that there are too many other neighbouring AP's, and most annoying they all use the American default channel 6 or 11 instead of the international 4-channel deployment setting. We now…

@Zyxel_Jonas No problem, found the error here while I already collected the right download over on the support pages.

Currently I'm running our WAX650S on a GS1920-24HPv2 with PoE+. The configuration is forced to full power. On the status page that is confirmed (shows a star on the status page). According to the GS1920 the power used varies between 10 and 15W. Nowhere near 30W. There are 20 to 25 wifi clients connected, most use 802.11n…

Links seem wrong... the text shows "Zyxel GS1920-24HPv2 - V4.70(ABMI.6)" but the actual link downloads GS1920-24HPv2_4.70(ABMI.5)C0.zip

OK, I took one of our stations and upgraded back to v6.25 - cleaned the configuration to only the ones for base operation (no enterprise authentication). This is the result after just two days. Memory Usage went gradually up from 45% to 64%, about 10% per day. And still going up. I have two diagnostic sets, to which email…

@Zyxel_Bella: Earlier this week I found time to start a diagnostic. Upgraded one unit back to V6.25 and again memory went up. Starting around 46% up to 64% in just two days, and it was still climbing. Configuration was cleared before the upgrade and set to a minimum for base operation with Rogue AP detection on. Today I…

Update: +7 days running on V6.20(ABRM.0) and still on 44% memory use. Won't update back to V6.25 now. Will have to wait for V6.30, hoping that this memory bug is removed then.

update: Now running on V6.20(ABRM.0) for more than 5 days and still on 45% memory use. Config and network use was not changed after downgrade. 

OK... within 18 hours memory use went up from 43% to 60%. So we reverted back to V6.20(ABRM.0) from april 2021. We'll monitor this one for a couple of days. @Zyxel_Bella We're running general network applications, like MS Teams or Google Meet on daytime with less than 10 clients. Mixed with streaming (video, audio,…