-
Firmware USG 100
hello I am looking for a newer firmware for an old usg 100.Does anyone have this available? current installed Version 2.2(AQQ.0) from 2010.
-
Unable to open port /NAT on USG40W
I have followed both of these guide to a "T" and my USG40W refuses to port forward: https://mysupport.zyxel.com/hc/en-us/articles/360003880919--ZyWALL-USG- How-to-open-ports-on-a-ZyWALL-USG-router-Port-Forwarding-NAT- https://support.zyxel.eu/hc/en-us/articles/360001390934-NAT-Rule-Configuration-on-a-USG-Port-Forwarding- I…
-
How do you change a device status to 'Inactive' on MyZyxel?
Greetings, I am trying to figure out how to change a particular device's status to 'Inactive' while it is in the process of an RMA. It hasn't been connected to the network for about a week now, and yet it still shows as 'Active', even though we have replaced it and the new USG60 is showing as 'Active' as well. I am hoping…
-
Security Advisory for firewalls published 19 july
https://www.zyxel.com/support/Zyxel-security-advisory-authenticated-directory-traversal-vulnerabilities-of-firewalls.shtmlwithout the damned link to wk28 file. The way Zyxel is managing this occurrencies keep looking bad, uncomplete and unsatisfying.
-
SSL VPN Secuextender and MacOS 13 Ventura
SecuExtender for MacOS the latest version is 1.2.4.1 and it support MacOS 12.3 MacOS 13 may have compatibility issue between SecuExtender 1.2.4.1. We will release new version at 2022Q4. Please do not upgrade your MacOS to 13 before new SecuExtender is released. Or you can use L2TP/IKEv2 VPN tunnel as backup solution.…
-
Wan2 on usg60w
I changed my Wan2 provider previously configured with PPPOE account, and working as failover. Now, with new provider, I don't have any pppoe credentials, and the wan2 connection doesn't work anymore (i simply connect wan2 port to my modem/router). How must I configure the wan2 connection? Do I need to remove the isp…
-
Timeout reaching category filter
Since this morning i noticed that my USG300 is unable to reach category filter and every query get a TIMEOUT message. It's a known issue common to everyone or my internet provider did something wrong with the upper firewall? Does anyone knows the address(es) of the category filter so that i can check if the server can be…
-
SecuExtender inconsystent connecting to USG FLEX 200
I the past few months we noticed inconsistency connecting SSL_VPN to USG FLEX 200.Sometimes is connecting sometimes not. Have the same VPN configuration for a long time and have been using it for years. Installed the latest firmware and running Secuextender 4.0.4.0 last night I got connected but this morning cannot. I'm…
-
ZyWall 110 to USG Flex 500 Upgrade - possible?
I have a ZyWall 110 and would like to upgrade the firmware to USG Flex 500 to enjoy further features. Is this possible? or do I need to discard the ZyWall 110 and buy a new HW platform?Thanks
-
Limitar banda por ip
Srs bom dia, existe uma possibilidade de limite de banda (internet) por ip no firewall USG110 Zyxel? se sim, como? Good morning, is there a possibility of bandwidth limit (internet) per ip on the USG110 Zyxel firewall? if yes, how?
-
USG210 as AP controller access local network
I have a USG210 as AP controller. See below. Please, can anybody tell me how I have to setup the USG210, so I can access the fileserver with the laptop.
-
ATP100W max number of IP Address objects
What is the limit to a number of IP address entries for ATP100W? For example, ZyWALL110 allows max 300 entries.
-
Tell Us What You Think About Zyxel Astra Preview Edition
Hello there, welcome to our customer survey of new
Zyxel Astra Service—a cloud-based engineless endpoint is designed to block the
threats and secure mobile working for corporate and BYOD into your network. We are always working to make our service catered
to your needs, so your thoughts are important to us! Your feedback…
-
USG200 close WAN connection every 25 minutes
Hello i have an old USG200 and on WAN2 we don't have problem, on WAN1 i connect correctly but after 25 minutes it insert status is inactive and stop communication. I need to swith to WAN 2, renew the DHCP of the firewall port WAN 1, switch to WAN 1 again and is work for 25 minutes.
-
VPN100 - Allow incoming L2TP VPN based on hostname
Hi, I'm looking for a way to allow/disallow incoming L2TP VPN connections based on the hostname of the connecting computer. Would that somehow be possible? Thanks!
-
Problems with uploading and restoring .conf - atp100 v5.30
hi everyone, My issue is a normal procedure of restoring, in my case the conf file was made on the previous version of the firmware and while i tried to upload it, shown the message " auth error". Following zyxel's forum i notice that often Zyxfw had problem in uploading phase if the version written inside the…
-
USG 60W User configuration send code for e-mail and phone check not working
In the user configuration section there is a place to enter an e-mail address and phone number I assume for 2 Factor Authentication. After entering my e-mail address or phone number you click to send a code for confirmation. That does not seem to be working. I get no code for e-mail or phone. I am running version 4.72.
-
Certificate issue on a Windows Domain controller with Zyxel Firewall as gateway
I'm setting up a Windows Active Directory Server behind a zyxel Firewall. The AD server has the ATP 500 Zyxel firewall as the gateway. Every time i try to login in a computer of the domain, using a domain account, i receive the following Security alert: When i press "View Certificate" it says the problem is something…
-
How to organize local network routing through L2TP/IPsec for VPN tunnel clients?
Hello.How to organize local network routing through L2TP/IPsec for VPN tunnel clients?Local network - 192.168.0.0/24. VPN tunnel - 192.168.10.0The gateway for routing the LAN-VPN tunnel will be 192.168.0.10/24.How to configure network routing in such a way that VPN tunnel clients (192.168.10.0) see the Local Area Network…
-
ZyWall 110: SSL VPN disconnecting problem after update to 4.72 firmware
Hi all. SSL VPN SecuExtender disconnects after a couple of minutes if there is no traffic through the tunnel. Were is a problem after update to 4.72 firmware.