-
xs3800 port 10gb fiber mono up and down
HI, I have a question with the XS3800 setup and xgs2220-30hp. I have one xs3800 and six XGS2220 (4x54hp + 2x30hp). All switch are connect in fiber 10G. All config go ok. But I can't connect just an XGS2220-30hp. I can to see in the xs3800 monitor that xgs2220 goes up and down continuously. I changed both transceivers and…
-
XGS2220 and XMG1930-30 series switches - total number of LAGs
Hello! Could anyone clarify the exact total number (limit) of Link Aggregation Groups supported by the XGS2220 and XMG1930-30 series switches, please? I couldn't find it neither in the specs nor in the user manuals.
-
GS1200-8 webadmin not accessible through VPN
VLANs: VLAN 10 = management VLAN (10.0.10.0/24) VLAN 110 = users VLAN (10.0.110.0/24) OPNsense 24.7.6 as router/firewall I have three ZyXEL GS1200-8 switches on my LAN (firmware version V2.00(ABME.3)C0). IP address for one (used as example here; all 3 have same issue) of those is 10.0.10.40 with subnet mask 255.255.255.0…
-
Linking 2 switch XGS1930-52HP using SFP+ port
Hello, How can I link 2 switch XGS1930-52HP using SFP+ port at 10 Gb, and what I need to buy as SFP+ transceiver. The 2 switches will be placed one below the other in the same bay.
-
How to configer Synology DS 1815+ on Zyxel GS 1920 /24
Hi I have made a bond with 2 adapters on my syno Now I want to start using Virtual Manager and get the following then I go to the bond - Verwalten - Vswitch settings Now I don't know how to configure what. I think I need Port aggregation in the Zyxel, but do not know how to set this up correctly Pls help me newbie to get…
-
How do I configure GS1900 switches to pass both VLAN and non-VLAN traffic between one another?
I have two GS1900-8 switches. I would like to pass VLAN and non-VLAN traffic between them. I'm unable to figure out how to do that. I have configured both switches to have ports 5 and 6 on VLAN 20. So both of those ports are assigned PVID 20 and marked as untagged. I have connected the switches using port 1 on each switch.…
-
VLANs and gs1200-5
I'm new to VLANS and trying to set one up adjacent to my default vlan. I'm aware I need a router that supports VLANS and so I got an edgerouter x, and set it up to work as a standard router, using my ISP router in bridge mode. This works fine. I then added a VLAN subinterface for switch0 on my router - which is VLAN aware…
-
How to add Service-key for L3 Access offline to a XS1930
I bought a L3-Acess license for my XS1930-10 and want to use the switch as standalone. I haven't found a place to enter the license key directly into the switch, is this not possible? Perhaps it is possible on the cli?
-
Using MAC Address filtering on switch with Access Points connected
Hi, hoping someone might have some advice. I am trying to setup MAC Address filtering on a switch to limit which devices can connect. There are two VLANs, internal network and then guest WiFi. 3 access points in use. Would like several mobile devices to only access WiFi and several servers or workstations to allow access…
-
I haven't received an download link for the zon utlity although the e-mail address is correct
-
Very slow connections after implementing a XS1930-10
I purchased a XS1930-10 to upgrade parts of my network to 10G. It is connected through a DAC-Cable over sfp+-port to a Netgear S3300-52x-POE+-Switch, which connects with 10g (XS1930 shows 10g and the netgear aswell). Scenario 1: The XS1930-10 is attached only with dac -cable with the netgear (no other client is connected…
-
GS1008HP broken-down
hi, after barely 2 years of service the POE switch is broken, all the LEDs are flashing, despite the so-called lifetime warranty it is impossible to find a contact at Zyxel for support! Does anyone have a solution? BR Greg
-
ZYXEL XGS2220-30HP
After logging in to the switch (ZYXEL XGS2220-30HP) via the console, it is impossible to log in to the web interface. You have to reset the switch plus reboot the power supply. Is there a cure for this bug?
-
FW V4.90(ABPL.1)C0 seems to break IPV6 traffic on GS1350-26HP
I have applied FW V4.90(ABPL.1)C0 to GS1350-26HP as I needed to have port information exposed in SNMP. This FW does indeed brings this feature, but I am encountering a serious issue which forced me to rollback to previous FW version. As soon as I got the FW updated to V4.90(ABPL.1)C0 users complained about connection…
-
vision stencils
is it possible to find the visio stencils for the gs2220-10hp, gs2220-28hp and gs2220-50hp somewhere?
-
Zyxel OLT1408A-C and Third Party ONU
Hello everyone! I have one question. We use Zyxel OLT1408A-C in some locations with Zyxel ONT PMG5617. Some days ago, my bosses asked to try connect third party onu to this equipment. I know that Huawei and some other OLTs sopport third party ONUs. Is there any way to complete this task or Zyxel OLTs does not support other…
-
Enable only Per Vlan RTSP
Experts, I do have a GS1900-24E with VLAN ID 1, 2, 4. PVID 2 is used for Internet, PVID 4 is IPTV and PVID 1 is local lan. I did see some occurrence that STP did mess up with port1 and port 2 which caused that my internet went down for 3 minutes. How can I enable to do only Per VLAN STP? I have now disabled port 1 and 2 as…
-
XGS1930 after reboot 52 port (sfp) is down
After rebooting the XGS1930 switch, the status of the port in which the sfp module is installed is down. Because of this, the switch cannot get an IP address via dhcp from a server connected to another switch, and these two switches are connected via sfp. At the same time, the web interface shows that packets go through…
-
POE powered Switch
Hello, Does Xyxel have any Switch that can be powerd usion POE from another Zyxel Switch. Thanks. Ato_1
-
reset a es3500 switch to default configuration?
