- Last Active
It is funny that you never reply to what I am asking, but to something completely different. In my previous post I wrote all the numbers according to what is shown in Nebula for TX power, what is shown as specs for antenna gain in official Zyxel documentation and after your suggestion for including multistream gain, I…
But if this is true, then you violate the regulations for EU, because if I apply the EIRP formula EIRP = transmit strength (dBm) + antenna gain (dBi) + 10 log10(number of spatial streams) (dBi) – cable loss (dB), I get the following values: NWA210AX low 5GHz band: 16+6+6=28 dBm, while regulation allows up to 23. NWA90AX…
@Zyxel_HsinBo I asked some specific questions in my previous message but your answer doesn't cover any of them. The quesstions are very specific: For EU country (Greece, but I also tried Germany, Netherlands with same results) a. At lower 5GHz band (frequencies 5150-5350) NWA210AX shows 16 dBm while NWA90AX shows 23dBm.…
Can anyone from Zyxel reply to this?
As I said, I connected KS8000 device with ethernet cable. With latest firmware for NWA210AX (V6.45(ABTD.0)), KS8000 never connects to wifi. With previous firmware it would connect after several retries. I don't have the time to debug the issue for you, moving my NWA90AX from floor to floor to do testing. If your firmware…
And just want to add that on 2.4 GHz, NWA90AX reports 19 dBm while NWA210AX reports 20 dBm, with the allowed EIRP to be 20 dBm. So why we see 20 dBm for NWA210AX, for 2.4 GHz the antenna gain is included or not? And I want to mention that adding gain of antenna to the EIRP is actually incorrect method, since the energy is…
Specifications in Zyxel site give for NWA90AX: Antenna gain 2.4GHz: 3 dBi5GHz: 4 dBiAnd for NWA210AX:Antenna gain 2.4GHz: Peak Gain 5dBi5GHz: Peak Gain 6dBi So the difference is 2 dBi as I already mentioned and not 3 dBi. Also, what you say is not true, at least is not shown in Nebula interface. Even if I configure…
I attach screenshots where the different transmit power is shown in Nebula interface
KS8000 runs on latest firmware. It seems the problem is DHCP related because KS8000 reports itself as "localhost" hostname in DHCP request and this confuses NWA210AX, while it shouldn't interfere with DHCP at all. Support asked me to change hostname of KS8000 from "localhost" but this is not possible, since KS8000 and…
Just want to add that the issue was never fixed, even with the latest 6.45 firmware (actually it became worse). I have been forced to connect KS8000 with ethernet cable (which is only 100mbps unfortunately).
I don't want to exchange NWA210AX with NWA90AX, I bought NWA210AX to have it on my main floor and moved NWA90AX to other floor. Samsung TV is able to pick signal from different floor when 210AX is turned off, but obviously the signal is low. I want to fix the issue so that Samsung KS8000 can correctly associate to NWA210AX…
Yes, I will, but since TV wasn't working I connected it with ethernet cable. Please let me know in what status should I leave the TV? In wifi connection failure? In wifi connection to different floor AP and then roamed back to NWA210AX? When TV is turned off, it disconnects from wifi so even if I configure it now to…
I have already tried that, actually I had NWA90AX in ground floor before I bought NWA210AX (now NWA90AX is on the basement and upper floor). However I tried it again and of course NWA90AX works just fine on the place NWA210AX doesn't. You want me to have KS8000 in the state of connected but no IP?