-
NAS540 RAID5, replacing drive, no repair option??
I have three NAS540s, all with four 2TB drives. Each NAS is configured as one big RAID5 volume. I've done single-drive replacements before and I've always been prompted to repair the volume. As I understand it, with RAID5 I should be able to upgrade all the drives one by one, repairing the volume again each time I swap out…
-
NAS326 UPnP not working
Hello everyone. I just bought NAS326 and wanted to set up remote access. I synced the NAS with my PC, downloaded myzyxelcloud, updated the firmware, registered an account, set up DDNS but I am for some reason unable to set up UPnP. I checked my router settings, UPnP is enabled. I am not sure what to do. I have tried doing…
-
ZyXel router randomly loses connection
I bought this ZyXel LTE 3301 router for use with a SIM-card which is also new. About 1-2 weeks ago the router started acting up, cutting out or getting insane lag (pinging google.com via cmd.exe gave me 3000+ ms). A restart is always required to get it working again. Things that couldn't be the problem. * SIM-card (New as…
-
Nas 326 with ZCloud
Hallo I set nas326 for upnp use. I obtain an address: 77.18x.xx.xx Upnp Port all on Zcloud connect ( only the address, no https check) Now work,i can contact trought zcloud and browser, but i ask me of the address aboverabove always the same Thanks #NAS_July_2020
-
Installing Arch on a Zyxel NAS540, like this guy did with Debian
Hello everyone,, I've been using Arch for a couple of years. Been using it heavily on multiple devices but haven't looked too much into kernel building and such...I would like to replace the stock firmware on my Zyxel NAS540 with my own custom Linux. I found this…
-
NAS326 Upgrade HD and keeping old files
Hello, I am trying to upgrade my internal HDs on my NAS326. When I remove the internal HD and connect as external USB, I cannot access it(it shows as unformatted). It is not RAID, it is just a simple volume. Is there a way that I can connect an internal HD as external to copy the files to the new installed HD?…
-
NSA320S 100% CPU Usage
Hello I'm using this NAS, but it's constantly at 100% CPU usage. Sometimes I can't even access the web portal and my folders, probably because it doesn't have resources to load them. I can ping it, but I can't access anything. Rebooting doesn't help. It goes back to 100% after a couple of minutes. I use it only as a ftp…
-
Can I create two volumes, RAID1 and RAID0 on two disk NAS326?
I currently have 2 disks in my NAS and RAID1 volume but running out of space. My idea is to have a RAID1 volume to keep the data that requires more protection and RAID0 for other data. I can't just do it from web-GUI, but I see a software RAID on my NAS, md0 for system, md1 for swap and md2 for data. So the idea is *…
-
NAS540 data lost on harddisk after factory reset
Hi Guys, I hope you can help me. This is now the second time I have this problem. My NAS540 crashed last week and had to do a factory reset. After the reboot the system was telling me found new discs. Option was adopt it and after that I had to press okay to format the disk. I did not press this off course because all my…
-
NSA325v2 RAID 1 recovery
Hi, I
have had my NSA325 for a few years now. It is configured with 2x5TB WD Red
HD''s in RAID1 (mirror) configuration. Recently, it has reported that the RAID
was degraded and SMART was reporting that DISK 2 was bad. I replaced DISK 2 with
another 5TB WD Red HD that I had but when I go back into the web console it
shows…
-
NAS542 inaccessible due to 16TB limit
Hi, I have a RAID-5 (single volume on disk group) setup with 3x6TB HDDs to which I just added a 4th one. All was fine until I tried expanding the volume from the web UI to the maximum available capacity (16.3TB). Now I cannot access the share or nor the web UI. I no longer hear the boot successful beep either. My NAS has…
-
Can both network cards be assigned IP from different networks on nas540 ?
As it is known, there are two network cards in nas540. I want to use cifs, nfs etc. default jobs for first network interface, and then I wanna use iscsi service for second network interface. So I assigned a rope from two difrerent networks to netwok cards, for example; eth0 -> 192.168.100.0/24 (vlan 102) eth1 ->…
-
Checking HDD SMART data with a NAS326?
Hello. Is it possible to check and observe the SMART informations of the harddiscs (bad sectors etc.) in a NAS326? Perhaps with a log. To show and save every change (new bad sector etc.). If the counter is rising, i will call the seller of the used HDD. And is there a automatic alarm, if a HDD in a RAID 1 does not work?…
-
Lost MetaRepository on NSA320
After a long time logged in to the admin page.Got there the message to upgrade MetaRepository version 13 to 15.Acknowledged the upgrade but apparently it failed. Refreshing the admin page it again asked to upgrade.Then put the recent web_prefix file in the NSA320/admin/zy-pkgs directory, hit the Retrieve button, the…
-
Print server on NAS542
Hi, I havent been able to use my printer (which worked with cups in Raspberry Pi). My printer appears "Offline" and if I try to delete it or rename it I get Error 500 How can I reset cups in the Nas542? I tried via SSH but I just get permission denied trying to delete the .conf files related with the printers Thanks
-
NSA325V2 stopped streaming after disc filled up
The CPU always runs at 100% and seems to be doing some disc writing all the time. Anyway if filled up one day and then stopped streaming to my various audio devices. I removed some files to allow 11% space but it still didn't restart. The Logitech Media server still is available but not the usual NSA325V2 which I assume is…
-
NAS540 - Troubleshooting email settings
As far as I can tell, the NAS540 can only send email to the unencrypted SMTP port 25 (which is ridiculous). Because of this, I set up E-Mail Relay on a Raspberry Pi to forward to GMail's TLS SMTP. I know it works, I did a quick telnet test from my Windows desktop. I don't currently have it configured to require credentials…
-
NAS520: Restore access to lost volume/disk 1 [SOLVED]
I have lost access to volume 1/disk 1/sysvol. I can logon to the NAS520 and when I choose "Storage Manager" it tells me that there is "No Storage" on the internal volume (external drives are not connected). Obviously, I can create a new volume but this will erase all data on the HDD will be lost. However, when I click on…
-
NAS540 vs NAS542
In this case all 4 disks are getting old(ish) and quite full as well. Option 1 - Replace disks with new, bigger ones. Option 2 - Buy a new NAS542 and disks. Is worth upgrading from NAS540 to NAS540? Any obvious reasons?
-
Experiences with XGS1210-12 Managed Switch
I just bought one of these for a home virtualization lab setup. I have a NAS server with 2 1gbps connections and a lab virtualization server with the same. I have a hardware lab firewall to separate the lab from my main home network and a port for my laptop. I have found it to be a good fit so far. The VLANs, trunking and…