-
Site to Site VPN Quit Connecting
Anyone with Site to Site VPN just suddenly disconnected? My Flex 500's will not reconnect. I've deleted configurations. Started over. Zyxel engineer looked at settings, deleted settings. Nothing!! Any ideas?
-
atp100
Good afternoon. I am configuring the ATP100 hardware firewall in transparent mode, created a new object, a new bridge, and disabled the last two ports in it. The rules created in the firewall control the passage of traffic through the bridge. Is it possible to redirect DNS traffic, for example, all that goes through the…
-
VPN IPsec entre USG300 et USG40 FREE PRO
Bonjour, Je viens de changer d'opéateur pour passer de Bouygues à Free Pro. Suite à ce changement, impossible de monter un VPN entre un USG300 et un USG40. J'ai créé une DMZ sur la FREEBOX PRO. En log, sur l'USG300, j'ai "[COOKIE] Invalid cookie, no sa found [count=2]. Si quelqu'un pouvez m'aider ou m'aiguiller. Merci et…
-
ZyWALL USG 20 Firmware 4.10
Hi. I try to update my USG 20 (non wireless) fomr V3.30 to the newst one. Unfortunately the earliest firmware I able to download is 4.16. But I need the versions between as the updgare not working strait to 4.16. Can I find all the needed files up to V5 ?
-
Upload config.conf files on different devices
Good morning everyone. I have a question. I have customers who have different security devices: Atp100, Usgflex200, Usgflex100. My question is: if I back up the configuration via config.conf file, is it possible to upload a config.conf file of an Atp100 to a Usgflex100 if necessary? Or Usgflex200 on a usgflex100 or Atp100?…
-
USG FLEX 50 VPN - Split DNS help
Hi, I have recently setup an IPSec VPN (client to site) on my USG FLEX 50. It is working fine on all the devices I need it to work on. I recently came around an issue regarding DNS. I have a local DNS server that's setup in the USG's DNS settings and it is working fine for all local devices using DHCP. However, with the…
-
ZyXEL SecuExtender "request configuration from the gateway"
I have a problem setting up Client 2 Site with IKEv2. On the firewall I already have a Site 2 Site with preshared key which works fine. I now want to add a client 2 site, but as long as the Site 2 Site is turned on, I cannot connect with Secu Extender, unless I turn off "Request configuration from the gateway" This means…
-
Looking for ZyWALL USG 100 firmware version 3.30(AQQ.2)
Hello and good day everyone, I'm looking for version 3.30(AQQ.2) firmware for a backup ZyWALL USG 100. I looked around and the closest versions I found were 3.30(AQQ.0) and 3.30(AQQ.3) in a forum post here. Does anyone have it available? I am currently using version 3.30(AQQ.7) but need the specific firmware above to…
-
IKEv2 Certificate Based on iOS 17.03
Hello Community, after getting a new apple device (iPhone 15) with the latest version (17.0.3) I am not able to get my IKEv2 VPN running. With the previous apple device (iPhone X) all was working fine. The configuration has not been changed on the ZyXEL (USG20W-VPN) side. Please see a screenshot of the configuration: After…
-
Set up Firewall as Switch
Since im always bored i tried to set up a USG40W as a Switch and i cant get it to work. I disabled Policy Control since i only want it to be a Switch and not a Firewall. My DHCP Server has an IP of 192.168.69.1(255.255.255.0) and it will give the WAN Port on the USG a IP(192.168.69.17) but it will not give an IP to any…
-
USG FLEX 200: is 2FA (Google Authenticator) supposed to work on L2TP vpn?
Is 2FA supposed to work on L2TP vpn? I did some test and it didn't work. The tunnel goes up, and traffic starts to flow. Even if the user doesn't go through 2FA process.
-
USG FLEX50W (20W-VPN) Factory Reset Not "5 Seconds" as stated in Manual
Last Saturday, I attempted to perform Factory Reset of USG20W-VPN, since it was compromised with unknown administrators in the User list, on older FW (prior to 5.39). Below is from the manual (PG 912): 1I Make sure the SYS LED is on and not blinking. 2) Press the RESET button and hold it until the SYS LED begins to blink.…
-
ZyWALL SecuExtender Two-Factor Authentication
Good afternoon I enabled the two-factor authentication method via Google Authenticator, but here we use ZyWALL SecuExtender to connect via VPN. When I log in, it goes straight in without requesting authentication via Google Authenticator, does anyone know what it could be? Print Log in through this software and do not ask…
-
How can I migrate our USG210 to USGFLEX500?
I converted our USG210 configuration to USGFLEX 500 but it's taking too long to migrate and it's not proceeding when I apply the configuration file. Can someone can help me please. thank you.
-
Cold boot FLEX200 SFP not coming online
USG FLEX 200 V5.37(ABUI.2) So had a power cut that my UPS could not keep everything running then when power come back the SFP looked dead after checking which is connected to a NETGEAR GS110T things I did. Reboot FLEX from UI no help Reboot GS110T no help Unplugged the power for FLEX and plugged back in SFP lights up and…
-
connection of two remote subnets through the main router
how to set up routing so that PCs from .3.1 are visible from the .2.1 subnet ? I have 2 usg20-vpn and one USG Flex200
-
block a bot
How to block a bot on our USG-50 using Security Policy.
-
SBG3500-N000_1.01(AAON.9)C0
Hi, I can not find this firmware. All FTPs are down and it doesn't appear in the download section or the support pages. How can I get this? The last one is: "SBG3500-N000_1.01(AAON.9)C0.zip" Thanks
-
Searching for Firmware SBG3500-N000
Hi, I can not find this firmware. All FTPs are down and it doesn't appear in the download section or the support pages. How can I get this? The last one is: "SBG3500-N000_1.01(AAON.9)C0.zip" Thanks
-
How to configure USG FLex 100 to allow clients to use outbound NordVPN?
My USG Flex 100 is blocking NordVPN (outbound) for clients on my network. Is there a common VPN out guide that applies to NordVPN?