-
XGS3700 - intermittently slow responses to pings and CPU over 100% messages in log
I was making some changes to the configuration of my XGS3700 switch stack and experienced occasional slow loading of pages in the web user interface. Sometimes taking as long as 2-3 seconds for a page to load. I decided to run a continuous ping from a PC connected to the XGS3700 stack and saw intermittent slow response…
-
Seperate Networks
All, I want to do the following: 1. Connect port 1 to ISP Ethernet (ISP uses VLAN 4 for IPTV). 2. Connect port 2 to router WAN side excluding VLAN 4 3. Uses port 3 till 8 for IPTV (VLAN 4) 4. Connect port 24 to Router LAN side 5. Uses port 9 till 23 for local switching I assume above is possible? I have a TP-Link now doing…
-
VLAN with non-vlan aware router
I have a GS1900 switch attached to my router on port 1 (Asus RT66U), 2 wifi access points on ports 2 and 3 (TPLINK EAP245V3) with no vlan setup. Everything works ok. My router handles DHCP and gives access to the internet to all devices connected. I want to switch this to use VLANs so that I can better segregate from…
-
GS1910-48: How to make a VLAN Trunk? (Firmware V2.00(AAAZ.0)C0)
Hello folks. I have recently purchased a GS1910-48 and updated the firmware to version V2.00(AAAZ.0)C0. I am very familiar with Zyxel switch GS3700. But the interface of GS1910-48 is quite different. So, what i want to do is: - Configure VLAN 10 on ports 1 and 2. - Configure VLAN 401 on port 4. - Configure VLAN 402 on port…
-
GS1900-24HP
hi.need help pleaseI turned on the zyxel for the first time and connect through 192.168.1.1 nothing strange so far when naming the ports and do other configuration on the system I loose access to the page 192.168.1.1 I've already turn off the switch and also reset the switch but still cannot have access Can anyone help me?…
-
Why there is no GMT +5:30 time zone in GS 2200, 2210, XS3800 and XGS4600 Switch
Hi, we are using 150+ Zyxel switches, we are in +5:30 time zone but there is no option to select our time zone in mentioned switch. can any one please help me to resolve this issue ? Regards,Kaushik
-
Who here own a GS2220?
Hi Some Support Member here think its the Switch I want. Well many thinks looking good. But there are some question left I have for someone who own one. Please Note I dont want to use there Cloud stuff. I got a ATP200 and use Zyxel AP to. Thanks
-
New to VLAN's - could not figure it out...
Hi, Under covid-19 conditions, where every family member is at home (work & education), I wanted to redesign my home-office network. I've got two Zyxel GS1200-8 switches and have the following design in mind: * VLAN 1 - outside towards Internet / will not be used unless emergency * A dual NIC SBC based router/firewall…
-
GS1900-16 - No IP from upstream DHCP server for voice VLAN device
My landscape consists of a UDM-PRO providing DHCP for two subnets named LAN (VLAN1) and SIP (VLAN10). The configuration on UDM-PRO works fine for any devices directly connected to a UDM-PRO port. In fact, it even works for a phone connected to an unmanaged switch connected to another port of the UDM-PRO. The only device…
-
Re: Anybody Use Zyxel Switches?
-
When does new L2 Switch arrive?
Hi The XGS2210/GS2210 Series is a little bit old. The only "new" is GS1300. Someone where mention here that "some new one" will come but no infos which one (L2 or now) and when. So does anyone have insider Information? Thanks
-
XGS1930 Vlan Trunking
I just purchased an XGS1930 switch, this is to replace an old cisco switch. the old cisco switch has the following configuration: ports 1-45 vlan 1 port 46 - Trunk Port with all vlans - Temporary port for XGS1930 testing and configuration port 47 - Trunk Port with all vlans - 2nd SwitchPort 48 - Trunk Port with all vlans -…
-
VLAN trunking between GS1910-24 switches for a guest network...
This should be a relatively easy setup, but my attempts at getting this to work have failed. I've got three GS1910-24 switches (v2 firmware). What I'm attempting to do is create a guest VLAN network across the switches using VLAN ID 20. [SwitchA - Port 3]<------->[ Port 24 - SwitchB - Port ??]<-------->[ Port ?? - SwitchC]…
-
GS1900-16 Firmware update
Having a problem updating firmware on two GS1900-16. When I go to the Web ap page to update firmware the page is not complete. Like it has an issue with Web browser but I have tried several on MAC and Windows. Also the firmware file 2.60(AAHJ.1)C0.bix I downloaded does not seem like it will work when I try to select this…
-
Anybody Use Zyxel Switches?
I'm in the process of upgrading my home network and have been looking at getting some sort of managed switch (just using standard home routers at the moment). In my search I found these Zyxel switches and was wondering if anybody here has used them before and what they thought of them. They seem to tick all the boxes of…
-
How to restrict some eth ports of Zyxel GS2210-24 Switch to access limited Multicat IPs & UDP ports?
Hi, I have a personal network on which I have different network applications are running on different multicast IPs and UDP ports. I want to give an ONE WAY access to my Friend to some particular Multicast IPs and UDP ports. But to secure my network and limit him not to access anything else on my network than allowed…
-
GS1900-24 webGUI: bugs? Missing functions?
My GS1900-24 is running fine, even now with the VLANs: stable and fast. The only problem was getting there: I found the web gui somewhat buggy: - it only runs in the browser's incognito mode (in normal mode it is gone immediately after login) - if I accidentally "touch" the dropdown button at the top of the list, it resets…
-
Whats Transceiver SFP+ are compatible XGS1930-28
I am desperate, I have tried several fiber transceivers and there is no way that the switch will detect something very strange.I have tested Finisar FTLX8571D3BCL, GTek. Has anyone tried them with any SFP + other than the original Zyxel?
-
GS1900-8HP/10HP - automatic password reset?
We've have a GS1900-8HP and a -10HP in use. From time to time the items reset their password by their own! Means, when I try to log in with the user defined password it does not work anymore. Instead the standard password is active. Also the factory setting is in use. Why? There is no access to the hardware for anybody. So…
-
Auvik - Integration
Hi all, We've recently switched to Auvik monitoring, it seems our Zyxel switches aren't providing data to this platform, is this beyond the current capability of Zyxel switches?