-
NWA50AX Pro TWT enabled?
Does the NWA50AX Pro have TWT enabled on firmware V7.10(ACGE.2)? I have clients connecting to this AP that are indicating TWT is not enabled. Is this correct? I've seen a post saying it was temporarily disabled in an earlier firmware due to client compatibility issues. Is this still the case for the NWA50AX Pro and where…
-
Wireless Bridge
I need to configure NWA55AXE to connect as repeater with wifi bridge to router WiFi DX3301-T1 (internet access) and a local switch with PC and other devices, but I am not able to connect to any WiFi device and his SSID is not visible to wifi scanner. May please help me? Thanks, Frediano
-
Framed-MTU is too high for EAP authentifications
Hi, We're having multiple issues of MTU across multiple remote location using either an AP NWA90AX, or the wireless from their USG 20W or FLEX 100W router. The ethernet frame from the AP to our radius server (Windows NPS) containing the user certificate is dropped at the router, before going into the IPSec tunnel to where…
-
FWA710 System Failure
Hi all, sorry but I am completely lost. I just got a FWA710. I added a SIM and the LED for the WAN turns Amber. However, the status LED is Red. When I log on to the management site, everything seems to be ok. I do not see anything to be fixed but I do not have Internet access. Can somebody help me? Thank you Roger
-
Reset NWA55AXE
How can i do a factory hardware reset on NAA55AXE? I recently bought an ‘open box’ and now regretting it since the device was registered in the store where it was ex-display from. When I add this to Nebula it just states it as offline all the time even though the green LED is on and seems to be receiving data. When on I…
-
NWA130BE - Mesh / Traffic
I just installed two NWA130BE in my home. So far, I am not massively impressed but I'll give it time to figure out. One question I have is why does a 'client' show connected to both wireless devices as per the screenshot. Is this expected or additional routing for no reason? Keeping in mind, my main floor is plugged into…
-
NWA 1123 ACHD mounting plate
I have an NWA1123 ACHD access point that I have misplaced the mounting plate for. Is it possible to acquire a replacement?
-
Can't cast to google cast device that is connected to different AP
I have two NWA55AX and one NWA210AX and can't cast to google cast device that is connected to different AP than the device Im trying to initiate cast This is very annoying and I assume quite frequent problem and should be fixed?
-
NWA50AX as repeater, power only over PoE?
Hi, I have 2 NWA50AX in simple "Root" and "Repeater" mode. The root is normal PoE, both data and power. In testing, I could not get the 2nd unit to work as repeater until I removed the PoE/data cable and used the adapter for power. This makes sense if the WiFi connection and the ethernet connection were conflicting…
-
NWA55AXE débit internet limité à 90 MB/S !
Bonjour, j'ai configuré le NWA55AXE, j'ai bien sélectionné les trois bandes 2,4 5 et 6g, j'ai vérifié mes cables rj 45, mis à jour le firmware, mais le débit reste au maximum à 90 MB/S ! en direct je suis à 1000 MB/s. J'ai connecté pour teste un rj 45 entre mon PC et l'alimentation POE du NWA55AXE et le débit n'est que de…
-
Error CLI Number:4-NXC5500
Hi Community, Starting this week, i have been having an issue with NXC5500. The controller is not onboarding WAX655E APs. They are reachable via web access, responding to pings, etc. but offline in NXC. An issue is, every time i am working on the controller in APs management, i get an error-as shown in the image every time…
-
Disable AP Isolation.
My internet company just installed a Zyxel router and now I can connect several of my devices, including my google nest and my VR headset. I tried calling my internet provider and they are useless. I read somewhere I might have to disable AP isolation. So I registered onthe Zyxel site, entered my MAC ID and serial number…
-
MWA55AXE Disconnects
-
Vấn đề về broadcast trên Access Point
I am currently experiencing a situation. On a Switch device, two ports are broadcast and those two ports are connected to two Access Points. How can I check which Client device is causing it?
-
NWA130BE drops all 2.4ghz connections and wont let anything reconnect.
After about a week of having my new NWA130BE the device has been dropping all 2.4ghz clients and not allowing any to reconnect. A reboot solves the issue. I grabbed diagnostic info while all the 2.4ghz connections are disconnected. Whats the best way to get this to you? Also as far as I can tell nothing has changed between…
-
NWA50AXE menu manquant
Bonjour, J'ai acheter d'occasion un NWA50AXE, celui-ci étant géré par Nebulla control center, je l'ai intégré à mon compte NCC puis retirer afin de le gérer en autonome. J'ai bien le login et password par défaut. Par contre pas tous les menus. Avec Zylex One Network Utility, j'ai éffectué un reset configuration to default,…
-
Bigger IP range for DHCP
HI, I have a couple oldies NAP303 and NWA1123 And a USG lite 60AX This is for a client based wirelles network. so I can make the open wifi go to vlan 2 and make sure they get the IPrange there but the 192.168.x.x range is limited to 240 address ( ok 254) But I need more and the lease on the dhcp is min 1 day. Can i use the…
-
nwa50ax support please
Hi,I have an nwa50ax router and I accidentally sold it to the system and then removed it and now I need to put it in another one and it says that it is not possible because it has already been registered, please help, thank you.
-
NWA130BE MLO with Samsung Galaxy S24 Ultra
Love these AP's! Now that the firmware is stable I have been trying to use them in MLO with a Samsung Galaxy S24 Ultra. It is supposed to work with MLO but I have had No to limited success. I wanted to know if anyone else has had a successful configuration of the AP and the phone to establish an MLO connection. As shown in…
-
zyxel nwa50ax isolation profil
