-
Armor G1 - NBG6818
What is the password for for the exported log file "log.tar" ? It is not the login password for the router.
-
G5 Config Backup / Restore options
I had to reset and redo the config on my Armor G5 this morning. I was having trouble passing data. Durning the reset and setting up the G5 again, there was a message that stated the config is backed up to the Zyxel Cloud. Is this correct? Where is it? How do I restore it? Can I manually issue a save or is it done…
-
Zyxel Armor G5
For the hardware specs on this device, it pales in configuration options. It would be nice to have more flexibility/ configuration options as in prior devices such as Armor Z2. I would suggest the following: 1. Multiple SSID's with more configuration options, in main network and guest network. 2. Guest network availability…
-
NBG6615 - LOG page
Hello. How long does the LOG you have in your NBG6615 router ?My NBG6615 router has only one page or max. 20 lines.This is a very short LOG for some older analyzes, I think.Is it BUG or feature ?Firmware Version : V1.00(ABMV.3)C0Thanks
-
nbg6615 AC1200 scheduling not working
Hi,the scheduling feature on my NBG6615 Wireless AC1200 Home Router doesn't seem to be working. No matter what I set up, neither one wireless network won't turn off on desired times/days.I enabled Wireless LAN Scheduling, set time periods for each day of the week but no luck. Tried to disable wireless network so the…
-
Static IP address on Zyxel (and mac address) on the router??
Please clarify an
important doubt at this moment. I want and like
to use static IP address. So far until
today I have registered all IP addresses on the router. Using the Zyxel
1900 switch I understand that the correct location to register the static IP
addresses is within the switch, is this correct??? Please help!! Your…
-
NBG6515 is blocking my Cisco Internet Phone
Hey everyone, It appears that my Zyxel NBG6515 is blocking my internet phone. My internet works fine, the wifi works, but I can't get my phone to work. I know it's the router due to the process of elimination. I've connected the phone to a different router (DLink) and it worked just fine. I've farted around a bit in the…
-
How to access the NBG6616 after it's changed to AP mode?
Here's the change procedures from reset the NBG6616 to factory default to access it in AP mode. Please refer to below steps. 1. Press the RESET button on the AP more than 5 seconds to set the NBG6616 back to factory default. After reset to default, please connect the WAN port (the blue port) to the modem/router which can…
-
NBG6817 - WAN disappears
My
router NBG6817
is connected to Internet via PPPoE. Problem
is that after several days WAN suddenly just becomes disconnected,
even frontal WAN LED goes out. Sometimes it happens at night,
sometimes during the working day - considering that now is "working
from home" time - this is quite unpleasant. After restart…
-
How can i solve Aurora "Failed to read the configuration" error?
Hi, I have an Aurora cam which has been up and running for three years until now. Today it suddenly dropped out of network. First I reconnected it but it did not work. Then I tried rebooting and reconnecting it. That did not work either. My efforts of re-setting it up on my phone which I tried as a last resort also ended…
-
NBG6515
Hello, If I mount USB disk connected to NBG6515 router on Windows PC as a remote disk it says it has FAT32 file system. Which is not very convenient because I am unable to upload large files due to FAT32 limitations. Is it possible to change this behavior? Thanks. https://bestpornwebsites.pro/ hot xxx sites is the latest…
-
ZyXEL home routers seems to be my worst enemies
This is now my third different ZyXEL home router. I've had two with another ISP, which both just had random disconnects from the internet without it making any sort of sense as to what were causing it. I've had another ISP since though, which handed me a Technicolor router = No issues at all. Now i have changed to a new…
-
Zyxel Armor Z2 NBG6817 and VPN settings
Will ever the Zyxel Armor Z2 NBG6817 support the openVPN? Can someone graphically (with screenshots) explain how to setup on this router the VPN IPSEC? #Router_February
-
NBG-419N v2 Not Booting
I've been using this router model for a few years now, but suddenly it stopped serving internet, the connection to the router is always going on and off and i can't reset it. When i power it on, it seems to be booting but then flashes all leds and shuts off, leaving that on and off connection state. Could i get some…
-
NBG-418N v2 loses time settings.
Hi, I have recently purchased an NBG-418N v2 Firmware Version : V1.00(AARP.9)C0 I want it to stop broadcasting wireless signal between 08:00-18.00 hours. There is a scheduling option for this. But when I turn the access point off, all time settings are lost. Everything goes back to January 1, 1970. So, I cannot schedule…
-
NBG6615 changes the channel every few hours, ignores it as I assign it in the settings.
I use the router on 5 GHz band. It is good and makes good distance, but I faced one really bad problem. The router can't keep the channel. Even if I assign the channel explicitly, it still works like in "Auto" mode. After I installed and set up the router, I checked for and found the best channel that got least…
-
Can't Reset NBG6604
Hello I've got a Problem with my NBG6604 I can't reset my router and I can't get access to the administration side. I pressed the reset button for more than 20sec and nothing happens. The power led is flashing in a rhythm of 3 sec and the 2.4 GHZ WiFi led is on. Is there any possibility to reset the router? Thanks for all…
-
NBG6617: Port forward SSH (22)
How can I forward port 22 to my Git Server? All other port forwards work fine, but port 22 cannot be forwarded with the error message "Port 22 is used by system.". I cannot even SSH to my router, so what is this used for? #Router_June_2020
-
NBG6616 IP address setting
Hi, I recently bought a second hand NBG6616 router. I immediately updated the firmware to the latest version (8), and it seems to work ok. My main router is at 192.168.0.1, subnet 255.255.255.0 / I want the NBG6616 at 192.168.0.232, running as an access point. I am not able to specify the IP address, it reset to 10.0.0.1…
-
NBG6617 - many TLS sessions to AWS
Is it normal for a NGB6617 router to have many (about 1 per second) TLS data transfer sessions to something in the AWS cloud?I can understand it wanting to check firmware status, but this seems ridiculous and I'm wondering if it is hacked? Thanks,Paran0id #Router_Oct_2018
