-
[NEBULA] Issues: WPA authenticator requests disconnect: reason 1. Interface:wlan-1-1 Station
Hi Guys, I have just taken on a new job. One of my fist issues is issues with zyxel AP constantly going up and down. When check the logs I get the following: WPA authenticator requests disconnect: reason 1. Interface:wlan-1-1 Station: B8:63:4D:C3:4E:45 Have tired upgrading the firmware but issue continued. Would be very…
-
buenas tardes, tengo unos ap conectador a mi red pero cuando instale zyxel para realizar una vpn
buenas tardes, tengo unos ap conectador a mi red pero cuando instale zyxel para realizar una vpn perdi el control de los AP y no logro vicularlos me podrian ayudar
-
[NEBULA] Setting up multiple AP's
In our office we have setup multiple ap's using NAP 102's. The problem is that one NAP 102 only connects for short periods of time and then goes offline again (showing green, amber lights). The other NAP says it has an wireless uplink and the required ip adresses, but is not giving any internet. It has never had any…
-
[NEBULA] Add extra external IP and map service
Hi, I configured a NSG100 with a static public IP, it connects to the internet, everything fine. Is it possible for me to add three additional public IP's to the WAN1 interface? And, on top of that, map some ports on these 'extra' IPs to internal hosts? Ex: WAN1 IP: 1.1.1.1/29 WAN1 IP2: 1.1.1.2:80 to 192.168.1.10:80 WAN1…
-
IP Address Block (ranges) in Firewall rules
On the older USG60W/40W/20W-VPN security appliances, I was able to go to OBJECTS and create a block of IP Addresses. Then I could go to the FIREWALL and use the object I created to allow or deny access to those IP Addresses completely or on a schedule or use a different Content Filter Profile on them. How do I create a…
-
[NEBULA] Does the NSG200 have IKEv2 capabilities for Site to Site VPN
I need a cloud managed switch with IKEv2 due to an Azure integration
-
[NEBULA] NWA1123-ACv2 disable wizard after uploading config-script
I uploaded my config via SSH to one of my NWA1123-ACv2. After I login via HTTPS, I still get prompted for the wizard, but timezone and other settings have already been configured via script.How can I disable this?
-
[NEBULA] Best Practice for NSG behind router
On one of our sites we currently have a configuration like internet <-> external router (192.168.2.1/24) <-> NSG100 (WAN:DHCP-Client on external router, LAN1 192.168.10.1/24) <-> NSW (DHCP-Client on LAN1 of NSG) <-> NAP The additional router is responsible for the internet uplink and acts as voip gateway. It has a static…
-
LTE USB failover
Is it possible to configure an USB LTE stick on a NSG50 ?
-
[NEBULA] Having troubles configuring NSG50 with fiber
Hi, We have troubles configuring WAN access on NSG50 We activate WAN1 on Port 2 and set internet configuration (WAN IP, SUBNET & GW) and it's working We have fiber 100mbps but in this config : Port 2 is set on auto nego / full - duplex speed 100 But speedtest send this ... : If i activate speed 1000 on Port 2 WAN, the link…
-
[NEBULA] PPPoE Bandwidth Limited on NSG?
I am encountering an issue with an NSG200 on a gigabit CenturyLink PPPoE fiber circuit. It seems that the NSG200 is limiting speeds to approximately 450Mbps. This is likely due to the PPPoE processing that is required, but routers from other manufacturers don't have this limitation when hardware offloading is enabled. Can…
-
NSG50 with GS1900 and NAP102
Moin Leute, ich habe folgendes Problem ich habe einmal ein Gateway NSG 50 (cloud) dahinter ein GS1900 Switch an diesem wiederum sind die Accesspoints NAP102 (Cloud). Jetzt ist meine Frage an euch wie ich es mit dem VLAN richtig hinbekomme, sodass ich den Gästen unabhängig von meinen Geräten ein WLan zur Verfügung stellen…
-
NSG50 with GS1900 and NAP102
Moin Leute, ich habe folgendes Problem ich habe einmal ein Gateway NSG50 (cloud) und dahinter ein GS1900 Switch an diesem wiederum sind die Accesspoints NAP102 (Cloud). Jetzt ist meine Frage an euch wie ich es mit dem VLan richtig hinbekomme, sodass ich den Gästen unabhänig von meinen Geräten ein Wlan zur Verfügung stellen…
-
[NEBULA] Nebula Pro Pack Feature: Advanced IGMP & IPTV Report
IPTV is a common application in hospitality especially
in hotels. It streams analog TV channels over IP multicasting. While people
enjoy the benefit of cost saving from typical coaxial cabling and analog
equipment, the evolution of technology introduces new challenges. For instance,
digital TV makers are far less familiar…
-
[NEBULA] Nebula Pro Pack Feature: Advanced IGMP
Nebula supports basic
IGMP snooping function for broader audiences while the professional pack adds
granular settings for IPTV. The Professional pack supports “Advanced IGMP”
which is specifically designed for IPTV adoption. Users can customize/switch roles, modes, and IGMP timers for effective bandwidth management in an…
-
[NEBULA] Nebula Pro Pack Feature: IPTV Report
IPTV
Report provides visibility to
hotel owners for their IPTV channel usage. They can easily collect statistics
on how many channels are being watched, the most popular channels as well as
the least watched channels based on specific date and time. The information can
help their decision making process for effective…
-
[NEBULA] Change Nebula Control Center Owner
Hello. I need to change the Nebula Control Center account owner due to a change of company that will manage the customer.How should I proceed?
-
[NEBULA] VPN between two NSG100 devices (both behind NAT)
Hi All, I have one NSG behind a cable modem, and one NSG behind a 4G modem. As I having trouble to find which NSG to blame for not connecting to each other I am trying first to connect from my mobile to the NSG, so I can check them separately, assuming that helps to find how to connect both NSGs to each other. With help of…
-
[NEBULA] Mesh
i want to create a guest network at another building. Can we create a guest network ssid on NAP102 on building1 and then mesh om Building2 and Connect a cable from the nap pn building2 into a switch? And then feed cabled computers on building 2 With this guest network? Will it work?
-
[NEBULA] Is it possible to expose a web server to internet
When I acces to my IP adress from outside I see the Zyxel NSG admin page (port 80 and 443) instead of my Web server. I have configured virtual servers in firewall parameters for both ports but it doesn't redirect to it.
