-
GS1900-E24 perfectly running but unreacheable via https
Hi. I am searching some help for this problem. My switch is perfectly running as switch, but I am not able to reach it via web interface. Firstly I tryed at last saved address, secondly after keepeng pressed reset button for 15 seconds, (assuming 192.168.1.1 default address) I set my PC to 192.168.1.10 but nor me nor ZON…
-
how to set half duplex / full duplex on a GS1200
I found how to set the speed on a given port but don't see how to set half/full duplex. I need to set the port to 10M but full duplex (I believe the switch will default to half duplex when setting the speed to 10M).
-
VLAN rogue-connection
I have a network consisting of a handfull XGS1930 switches, a NXC controller & firewall. (The explanation here is simplied from the actual setup) The network is divided into administration 192.168.2.0/24 , with a windows server as DHCP server Guest 192.168.10.0/25 , with a router as DHCP server. management 192.168.3.0…
-
Adding LAGs kills AP Management
Have a XS3800-28 acting as the campus core switch at a single location connecting to individual XS1930-12HPs which have connections to a USG Flex 500 and multiple WAX650S, WAX610D, and one WAX510D (8 total). Two pairs of OM4 fiber connect at 10GB each to each XS1930 to the XS3800. If we have just one pair between these…
-
GS1900-24 dead within hours of update to V2.70(AAHL.0)
After many years of operation and numerous other successful firmware updates, my GS1900-24 failed operation just a few hours after I uploaded V2.70(AAHL.0) from V2.40 previously installed. At the time, I noted the new firmware home screen was broken (Brave browser). Rendering of active ports / LEDs was misaligned with the…
-
Topology for Zyxel GS1920 48
Dear all, I have seven switches in room 1-second floor. I also have 4 switches in room 2-second floor. There are 9 switches on the third floor. All switches are Zyxel GS1920 48. I wonder how to set up and topology for this scenario. Thank you very much Best Regards
-
GS1900-48 recovery image needed
Hi there, I have an old GS1900-48 that has been switched off durig fw upgrade, and it does not boot up. The switch has a serial interface internally, which provides a way to recover it, but it needs an initramfs kernel image, that I cant seem to find. Anyone can give me a hand to save this nice hadware and return it back…
-
Need rack mount kit for my XGS3700-48HP
Hi, I have a long APC rack and I'm looking for a rack mount kit for the model in subject
-
mellanox 25G eth card on xs1930-10 by sfp28
I use a mellanox 4121A (25/10G) eth card , but there's no any Tx/Rx data, the firmware and driver is fine. so I guess maybe the question is the switcher , but I don't know how to config, anyone help? Thx a lot !
-
Mounting brackets for Zyxel GS1100-16
Hello, I am trying to mount my Zyxel GS1100-16 to a 10" rack. The router came with a mounting kit for 19" racks. Where can I find shorter brackets for GS1100-16 ? I think there is a Zyxel part, 1-004-05900005, that should work but I can not locate it in Greece where I live or in European Union. I bought the switch more…
-
With a Zyxel GS1200 do I need a router to get internet on my PC?
Maybe this is a stupid question, but anyway, I bought the GS1200-8 believe that I could connect it to my fiber box on the wall and then connect my PC and other home devices and they would run the home network and I'd obviously have internet on my PC, but I have no internet on my PC unless I from from fiber box - router -…
-
dual XGS1010-12 10gig passthrough
So i have dual of these XGS1010-12 switches both with two 10gig sfp+ ports. On one switch I'm using both SFP+ 10g ports. One to connect to my router and the second port to pass through to my second XGS1010-12 switches 10g sfp port. I seem to have a lot of issues were this is disconnecting the second XGS1010-12 when i put…
-
VLAN GS120015
I have a GS1200-5 connected to my router. I want to prevent port 2 on the switch from seeing any LAN traffic. Is this doable with a VLAN? I am running firmware V2.00(ABKM.1)C0.
-
hi.dslam is 6000
Hi, one of the dslam 6000 series cards, model 1372g-52, has been inactivated and gives a signature error message.
Guide me, thank you
-
VLANs cant communicate with LAN
Hi Community, I dont have experience about VLANs. I followed the instructions how to set up VLANs. Now my test-VLANs can communicate with each other as I wanted but from and to LAN there is no communication possible. I have an XGS1930 (Layer 3). LAN is 192.168.1.0, VLAN10 is 192.168.10.0 and VLAN11 is 192.168.11.0. Do I…
-
XMG3927-B50A Connect to FTTP (Full fibre)
I have a ZYXEL XMG3927-B50A connected to a FTTC setup with TalkTalk. My Zyxel then connects via (cat5e and cat6 cable) to 2 other routers as AP connection. My setup works great The parental control work via the Zyxel throughout my system and get great coverage/signal. Im due to change over to a Full Fibre Connection FTTP…
-
GS1200-8 802.1Q VLAN: Must all ports be connected to VLAN 1?
I wanted to separate a PC into VLAN2, but it should also be able to connect to the same internet router as for all other devices in VLAN1. I set the PVID to 2 for this PC/port and set untagged for VLAN2 and unconnected for VLAN1. Also I put the the internet router as untagged in both VLANs. But with this it cannot connect…
-
Packet loss on GS-4024 with VLAN
Hi! I have configured a GS-4024 with VLAN, but I have packet loss and it's acting like he is making pauses. I cannot find any info on the internet. Here is a part of the config file:; Product Name = GS-4024 ; Firmware Version = V3.80(LL.4) | 10/06/2008 ; SysConf Engine Version = 1.1 vlan 1 name 1 normal "" fixed 1-24…
-
May I get a firmware(for VES1724-56B2)?
Hello. We have been operating the switch(for VES1724-56B2 model). The problem in us is that we do not have any firmware file to restore. Do you mind if I ask that we can get a firmware(for VES1724-56B2)? - I could not find a firmware(for VES1724-56B2) in myZyxel-device management-firmware download. Thank you Adan Regard
-
Is this a good 16 port gigabit switch? If not, what are some good recommendations?
I don't have gigabit internet but want to future proof this purchase. Also, do I connect the ethernet wire from the modem into any of these slots, and then I connect a Ethernet wire from the switch to the router? Or do I cinema hd connect the ethernet wire from the modem to the router, then a wire from the router to any of…
