-
Cannot connect to my GS1900-24 managed switch any longer.
I thought my internet went down, I could not get it to work so I replaced the router with a brand new ASUS RT-BE58U and the internet was restored but the minute I plug the switch into one of the LAN ports the other 3 LAN ports on the router loose internet access. Research told me it was a possible IP loop but how is that…
-
Enabling DHCP with webgui on a XMG1915-10E
Hi, i am facing the issue that i am not able like others to receive an ip for the XMG1915-10EP like others. I also followed the already closed thread No one confirmed that this works and the thread is closed. I tried to do the procedure described in the post from support but after several hours i gave up. Could you please…
-
NAS326 encrypted by ransomware ("ANON RTS LOCKER", .anon extension) – no UPnP/DyDNS enabled, need he
Hi My NAS326 got encrypted by ransomware. All files now have the original name plus a ".anon" extension (e.g. photo.jpg.anon), and a text file ransom note calling itself "ANON RTS LOCKER" was dropped in the folders. The note demands 0.007 BTC and lists Bitcoin addresses, a TOX ID, and contact emails. What's confusing me is…
-
Need ACDJ firmware dump for Zyxel NR5103E – device flashed with wrong NR5103 generic firmware
Hi everyone, I need help recovering a Zyxel NR5103E (Tre Sweden variant). The device was incorrectly flashed buy a buyer who claimed it didn't work and used the site to send it back to me and get his money back stating it wasn't working when he got it (well, he had it for over a week when it stopped working for him). It…
-
WX3100 meshes with EE5301, then drops and reverts to factory network name
I can get my WX3100 AP to connect to my EE5301 router using the Zyxel app (over wired LAN). I then unplug it and move it where I want it, let it fire up, test the signal and confirm that it’s part of the network. A minute or two later it drops from the network and reverts its SSID. However if I connect directly to the AP,…
-
Site to site zone not saving in config
USG FLEX 700H V1.39(ABZI.0)ITS-26WK36-m12745 So at first I though this was some other bug then I looked at the config for site to site Zywall110V4 zone and it was set at none which is odd because I know I would of set that so changed it back to IPSec_VPN and save the config. But I could not put my finger on it as to…
-
[USG Flex H] - DDNS public IP - decrease minimum check period
Hello, I would like to decreare the minimum check period for a public check URL. Until now, the minimum is fixed to 5 minutes; this can be a problem, because, if the WAN IP change, the DDNS can check a public URL to know the new IP, in the worst-case scenario, only after 5 mins after the change. Is possible to change this…
-
Xs1935 -10 v xs1930-10 noise issue??
Hi I added yesterday new xs1935-10 to my network alongside my xs1930-10 which is about 1 year old. The xs1935 is so much louder/noisy. The fans sound like they are rattling/buzzing and not a smooth sound like the xs1930.... I bought this through amazon so considering getting an exchange. Views welcome please Thanks
-
[Research / Guide] Recovering the AX7501-B0 to Official Stock Firmware (UART, CFE, UBIFS Analysis)
Hi everyone, I wanted to share a technical case study and research notes on restoring a second-hand Zyxel AX7501-B0 back to official stock Zyxel firmware (V5.17(ABPC.8)C0) after acquiring a unit locked down with custom ISP firmware (V5.17(ABWW.5)C0). In this specific state, local management interfaces were inaccessible and…
-
USG FLEX 200H – Inbound UDP/5060 (SIP) not forwarded by Virtual Server NAT rule
ENVIRONMENT Device: Zyxel USG FLEX 200H Firmware: V1.39(ABWV.0) WAN interface: vlan7_PPPoE (PPPoE, dynamic public IP, referred to as <WAN-IP>) LAN interface: vlan10 (internal network 10.10.10.0/24) Internal server: 10.10.10.10 (Asterisk PBX, listening on UDP 5060) Remote peer: Deutsche Telekom SIP servers, 217.0.0.0/13…
-
Upgrade path GS1900-8HP
Hi, I would like to upgrade my GS1900-8HP (not v2), but I belief it is not advised to upgrade to the latest firmware version in my case. My current version is: V2.30(AAHI.0) | 12/14/2016 Can you advice me on the upgrade path and where I can find previous firmware versions? Thanks in advance! Regards, Niels
-
I want to change my router password
-
Apple
-
Policy route to VPN-tunnel on Nebula
Any plans to add VPN tunnel to policy route's Next Hop? Would enable to use for example USG LITE 60ax to branch offices.
-
FWA710 going offline
We have a FWA710 router which is going offline in time to time (daily). Sometimes minutes before going back online, sometimes for hours and needs to rebooted to get online. We have good 5G signal (less than -85db). This is what I find in the log, device went offline at 20:55, got online at 04:00 (Scheduled reboot). What…
-
Firmware image required for MES3500-24F and MGS3520-28F
Hello Zyxel Team, I am currently working on a firmware upgrade activity for the following Zyxel switches: MES3500-24F Current firmware: V2.00 Firmware date: 03/28/2012 Target firmware identified: V4.00(AABG.6) Target firmware date: 08/08/2018 MGS3520-28F I am looking for the latest supported firmware image for this exact…
-
firmware download V5.70(ACEB.5.1) C0
where can i download firmware version V5.70(ACEB.5.1) C0 for the Wireless Extender WX5600-T0
-
NR7302 (ex-Telekom firmware): 0 Mbps Download / 0.5 Mbps Upload with Public IP SIM - Routing issue?
Hello Zyxel Community, I am facing a severe routing/NAT issue with a recently purchased used Zyxel NR7302 5G outdoor CPE and I'm hoping some experts here can point me in the right direction. The device has a custom carrier firmware (ex-Telekom). I am using it in Italy with an ISP called Alpsim (running on the WindTre…
-
Default Zyxel AX7501-B0 password
Hey everyone After a brutal battle with my router that was ISP locked i managed to unpack and rebuild a working firmware i now am on the default ZYXEL page that does not have the isp's logo on it the issue i am now facing is that there is a password i do not know it is not the one on the sticker nor is it admin :…
-
NR2101 firmware V1.00(ABUS.1)b177
Unable to upgrade from this version. Need some help. Thanks