-
Incoming call impossible on LTE5398-M904 ?
Hi, is it normal that we can't receive incoming calls with a phone connected on port RJ 11 with the modem 4G LTE5398-M904 ? I can make outgoing calls but not incoming or I didin't find the good settings. However I put the setting to "Volte service" in voice mode. Is anybody knows why ? Is it like that for you ? Regards
-
NBG-418N v2 slows down permanently
Hello, i have problem with your router NBG-418N v2. It has V1.00(AARP.9)C0 firmware. The problem is that router has constantly lowered speed (cable, wifi). Full speed is 40Mbit, but after week or so speed is lovered to 5-9Mbit. Only solution for that is router restart. Can you help me with this please?
-
DX3301-T0 - WLAN AP only
I want to set up my DX3301-T0 as AP only together with its VoIP capabilities. How do I configure the device? I have set a static LAN IP address and WAN to Bridging mode (not using WAN interface right now). My device is missing the default gateway address, the DNS server and the NTP server. How do I configure that?
-
Question about Startlink IPSec
Hello, Does anyone did an IpSec VPN over starlink ? We've got 2 USG Flex 200, ISP fiber Router Between them, and a Starlink router in bypass mode as backup connection. IPSec is OK by fiber. For Startlink, the VPN is up but no traffic. I known the problem about CGNAT and public IP, but i not network engineer... Is there a…
-
LTE7480-M804 and NR7101 setup as VPN client
Hello, I have 10 4G routers (7x LTE7480-M804 and 3x NR7101). I want to set them up with OpenVPN. Is it possible to configure them as clients on a VPN network? The goal is to create a large virtual network under the VPN. If this is not possible, do you know another product of a 4G router outdoor with PoE power supply that…
-
Flash standard firmware on to AX7501
Hi I have a AX7501-B1-CH01V1F from my provider. I'll switch my provider end of january and he said i can keep the router. The thing is, it's flashed with a special software from my provider. It would be too bad to just throw it away. Is there any option to flash the standard firmware from Zyxel to the device? Regards
-
I want to connect my Zyxel EMG3525-T50C router as an repeater/extender ?
I have a TP Link AX1500 Gigabit Wi-Fi 6 Router and Zyxel EMG3525-T50C router. I want to connect my Zyxel router as an repeater but whenever i try to change the operation mode to " Repeater " and click apply its stuck loading . I've also added the Zyxel router to the TP Link EasyMesh network but the Zyxel router is still…
-
Help Needed to Configure Zyxel EMG1702-T10A as a Repeater
Hello everyone, I'm trying to configure my Zyxel EMG1702-T10A router to work as a repeater, but I'm having trouble finding the correct settings. I've accessed the router's web interface but couldn't locate the options for repeater mode. Here are the options available: DHCP Mode, Start IP Address, End IP Address, Max lease…
-
I try to login to 192.168.1.1 with admin and password CDDVLUBN (router).Get wrong user or password
-
NR5103E
I want to update this router because it has an update number Current Firmware Version: V1.00(ACIR.0)C0
-
DX3301-T0 Upgrade from ISP firmware
Hi, so I signed up with a new ISP, they sent me a nice DX3301-T0 router which I used for a couple of months, until they went bust. So I got another ISP and another new router… Is there any way of switching back to the stock/generic firmware? Seems a shame to bin a fairly decent router. There's no firmware upgrade option in…
-
DX3301-T0 - using VoIP behind a German FRITZ!Box
I have a FRITZ!Box 7490 as my internet gateway which also provides my phone capabilities. To connect two phones in my bureau (where I have only an ethernet line to my FRITZ!Box), I want to use the DX3301-T0 as a VoIP gateway. I have created a VoIP device on the FRITZ side, I have IP address as registrar, username and…
-
Parental control
I have model AM3100-B0 and firmware version V5.17(ABNY.9)E0 and cant seem to get parental control to work. I have tried to change AM to AM and PM to PM but nothing that i have registered in the PC seem to work. Any suggestions?
-
Do I need an ATA?
I have a Zyxel EX5601-T0 and need to connect a phone. Are the phone sockets suitable for a PSTN phone or do I need an Analog telephone Adapter? Thanks in advance. Chris
-
FIRMWARE NEEDED
Hallo Everyone, I might need some help i need the DX3301-T0 Firmware but the GERMAN Version the normal or GENERIC doesn't work here in Germany.This is how it looks in generic mode 5.50(ABVY.4)C0 vs how it should look 5.50(ABVY.4)D0 Thanks for the help everyone!!!!
-
Zyxel DX3301-T0 firmware
The last software update of this router was faulty, I reported it, it was removed from the library, but the new software has not arrived for about 3 months. My modem has been receiving low signal and giving errors for 3 months. When will it arrive? I cannot change it back to the old one. I cannot downgrade. Be quick,…
-
NR5307 5G NR Indoor Router with Nebula FWA710 (Zyxel 5G outdoor)
Hey, I have a question. Is it possible to connect the NR5307 5G NR Indoor Router with the Nebula FWA710 (Zyxel 5G outdoor)? In the instruction video I saw that the utp cable need to be connected to the WAN, but my indoor router only has 2 LAN. Product video screenshot of 5G outdoor: I’m using the NR5307 5G NR Indoor Router…
-
V1.00(ABMV.6)C0
Salve, Da quando ho installato l'ultima versione del firmware V1.00(ABMV.6)C0 per NBG6615, non funziona. Se collego la rete wan il tipo di connessione resta su OTTENIMENTO INDIRIZZO IP e resta sempre su 0.0.0.0 Da dove posso scaricare una versione precedente? Sopratutto, quale?
-
Isolate server from home devices on AX7501-B
Hello, I got a AX7501-B from my ISP since we got 10gbit optical fiber. I have been trying to isolate a server on my network without luck. The goal is to have it on some kind of separate LAN so it can't communicate LAN-LAN with other devices at my network because of security. I have tried with VLAN, DMZ, Interface group…
-
EX3300-T0 firmware update
Hi, I would like to update the firmware on my EX3300-T0 but the Zyxel support site does not list the model. Can I use the firmware for EX3301-TO which is provided in the link below? https://www.zyxel.com/global/en/support/download?model=EX3301-T0 Thanks in advance. Regards, CK
