-
Can't change interface settings on a USG20W (ok button disabled)
We use a USG20W, it's probably called USG FLEX 50W now. It's running for quite some years and we did not want to retire it yet. Anyway, if we open the interface settings of the lan1 interface, the ok button is disabled (right after opening the settings without changing anything). Probably because there is an error in the…
-
VPN L2TP not working since last update
Hi, On a USG20-VPN, I set up a VPN-L2TP working perfectly fine for several users. Since several weeks (it seems to be since last update) no one is able to connect on the VPN getting this error on Windows (sorry in French): On the USG20-VPN, I see only logs with IKE filter: Thanks for your help...
-
Upgrade from USG60 til USG FLEX 200
Hello, i am upgrading my firewall and i wonder if i can use the configuration file from the USG 60 and upload it to USG FLEX 200?
-
USG 310 - public IP behind PPPoE
Hello, how to correctly configure public IP behind PPPoE with dynamic IP? This is my configuration withou public IP: ! model: ZyWALL 310 ! firmware version: 4.70(AAAB.0) ! interface-name ge1 wan1 interface-name ppp0 wanTvinet account pppoe TVINET user *** encrypted-password *** authentication chap-pap compression no idle 0…
-
Content filter https issue
Hi, Router : USG40wfirmware : 4.65 then 4.70 We notice that all site with "https" were blocked. Investigating the firewall, I noticed that many website like google were classified as "unrated". So I checked with the category tester and I got an error. I think it is the issue. I did the upgrade to 4.70 but the issue remain…
-
usg20w can I use an existing mac address on the WAN Interface
Not seeing a way to do this thru the GUI but it would be nice so I don't have to hassle with the ISP when replacing existing Firewall... Thanks,
-
Disable 2FA for admin login from console on USG40?
I work remotely from the USG40, and when changing the admin password I clicked "enable 2 factor authentication". Now I'm locked out. Dumb, but true! I'm going on-site tomorrow, and will connect to the console port to try to regain access. Is there an easy way from the console to just disable 2FA for the admin login? I…
-
FTTH modem on USG60W
I have a USG60W and an ONT adapter of my fiber connection provider. Can I connect the ethernet of ONT to WAN port of my gateway USG and configure them like a PPPoE modem? I have tried but don't works. thank's
-
TX/RX Statistik
I'm confused about the RX/TX static at the dashboard of the ATP200.P2 is used as the WAN1 with DSL 100/40Mbit/sec. It is connected to a DSL-Modem over an 1Gbit/sec Ethernet wire. But at the statistic are shown through pass rates up to 9.000,000Mbps and more. These are more than 8,5Gbit/sec, more than the Ethernet can…
-
Sometimes the ARD Mediathek works but mostly not at ONE TV
Maybe I'm totally at the wrong place wrong and I don't know the right category - Sorry, I'm a new user of Zyxel..... So, I'm using the ATP200 on an 100/40MBit (Yes, it's lame .-( ) PPOE-WAN to my ISP. After the box configuration the most things gone well! But some things are - let's say - not clear: So, the most worried…
-
Problem Site to Site USG 210 and USG 20W
Hi I have a problem for connect the USG. I create VPN Site to Site, but not work. I use this configuration....but the tunnel not Up. https://support.zyxel.eu/hc/it/articles/360001378873-USG-ZyWall-Configurazione-da-sito-a-sito-VPN-IPSec USG 210 has public ip 93.40.x.x Local IP: 192.168.1.1 USG 20W has dynamic public ip…
-
UTM Statistic SecuReporter
Hello, it is possible that when I'm enable secuReporter, my ssl_VPN on usg210 slow down or that it's reduces the performance of the device?
-
USG 110 - How to create an IP Blacklist?
Just experiencing a lot of USG Alert Logs containing "abnormal TCP traffic detected" which originates often from same external internet IP addresses. No. Date/Time Source Destination Priority Category Note Message 1 2022-01-31 02:27:34 119.1.169.252:48336 ***.***.***.*** alert secure-policy ACCESS BLOCK abnormal tcp…
-
VPN Client internet
When I launch vpn client, i have access to the remote network, but i no longer have internet on my comptuer Here is ma setup IKE 1 - Adress Client - 0.0.0.0 Adress remote - 192.168.0.0 Mask - 255.255.0.0 do you have an idea ? Best Regards JC
-
June Incident: VPN 2FA & Disable HTTPS
We use 2FA on VPN for all users, this is reliant on the HTTPS service. If we disable the HTTPS from WAN, we cannot authenticate. Please create a review alternative methods to get us around this limit. Perhaps make it so the VPN connection can only access the HTTPS (internal IP) until authenticated, versus blocking all…
-
USG20W-VPN Dropping Local Devices Every 10 Or So Days
I have a customer with a USG20W-VPN running 5.10 firmware that appears to lose network connectivity (aka DHCP) to their devices on their local LAN every 10 to 13 days. I'm leaning towards it being a switch, but I cannot rule out the ZyXEL yet. They had a previous USG20W-VPN unit that we replaced already, thinking it might…
-
USG20-VPN => Firewall default functionality
I would like to install the USG20-VPN after the modem on my network in order to have a HW/SW firewall that would guaranty me the safety of the network of mine from esternal intrusion. No VPN application. Which kind of default functionality has the USG20-VPN for the external intrusion? If any, can you kindly describe them…
-
Backup Cellular drop in and out
Backup Cellular drop in
and out VPN300 V5.20(ABFC.0) Cellular ZTE MF823D
(CDC-ECM) So I found out my
backup Cellular is dropping out when my main DNS running bind by ISP
MAC reset and went over to my Cellular and found its dropping connection
pings by diagnostics > network tool fail then it starts working
only to fail for…
-
Signature update broken again?
Hi Is it correct, that the latest signatures are from 2020-01-20?
-
USG20-VPN configuration upload time
How long should this take? Currently been 20 hours and I've still got the "Please wait. File upload in progesss" box with the progress bar