-
Stuck with Vendor-ID-based-VLAN
I think what I am trying to do is not too complicated but I am stuck at a 90% mark I want to have ports splitting what comes in on its ports from the default VLAN 1 (which has a DHCP server) to VLAN 400 based on the Vendor Mac. From the MAC tables, I have what appears to work but there is no communication between devices…
-
GS1350- CLV not working
I have a new to me GS1350-6HP. Its running the latet 4.70 firmware as far as I can tell. Finding it very difficult to get the vlans doing what I want and am at the CLI trying to enable CLV mode (I am very familiar with cisco switches). The CLI guide for the 1350 says I should be able to enable, config, clv to enter clv…
-
XGS1930-52HP SNMP oids for defining PoE consumption on port
Hi, can anyone share the information about SNMP oids to show PoE consumption on ports for XGS1930-52HP? I`m looking for something, looks like CLI answer on request "show pwr": or WebUI: I know about 1.3.6.1.2.1.105. but this branch does not have an oid with ports PoE 'Consumption (W)'. Q: How I can get the PoE consumption…
-
Can the GS1920-24HP Backup be restored to the GS1920-24HPV2
-
SFP+ compatibility with Synology NAS
I have a Zyxel XGS1930-52HP router with 4 SFP+ ports. I am about to buy a Synology NAS (822+) with a 2 SFP+ ports. I am wondering if any SFP+ complient cable will work or if I need something special. I heard that some brand ask fort cable with specific tags to be compliant. The specific ref I want to use is 10G-TWINSFP+3M…
-
Port/Interface Dampening?
Does anyone know if this is possible to configure on a Zyxel switch? I was unfamiliar with the term until recently. We will be configuring two Dell PowerSwitches in VLT (Dell's version of MLAG) with a LAG from the VLT domain toward a XGS2210-52HP. Dell's VLT Technical guide suggests dampening (or equivalent) should be…
-
GS1200 & TP-Link Deco vlan
Hi, i'm trying to do a basic vlan using a guest network to connect all my 2.4ghz band devices to a deco mesh setup Port 8 - Main Deco M5 Router doing dhcp and handling th internet connection + 5ghz wifi and the guest network Port 7 & 4 2x satellite Deco s4 running the 5ghz main network and 2.4ghz guest vlan other ports -…
-
XGS1250-12 Fan not working?
Got my switch today, plugged in 3-5 1Gbit stuff, one 10Gbit and one 2,5Gbit. No sfp. unmanaged. After a while the switch got so burning hot that it crashed. A reboot gave me 3-5min before it crashed again. The fan never kicked on. I have since updated it to latest firmware wich should "fix" the overheating but the fan is…
-
Zyxel ES-2024PWR
Helo I'm looking for .bin and .rom to my switch, can't log on to the switch, found 390FW.zip at dd_cz posting but that did not work on my switch, get error. Hope for fast answer, it's a critical switch. Best Regards Mikael
-
GS1350-18HP, does not accept DHCP Offer from Meraki Firewall
Hello there, we tried to install a GS1350-18HP in our network. When Sniffing the traffic we see a DHCP request coming from said switch. We also see the DHCP reply from the firewall being sent to the Switch. But no reservation takes place. The switch does not respond to the offer. Connected Accesspoints have no problem…
-
VLAN Setup for WiFi across multiple APs
Hello! I need help configuring my home network. I have 3 Zyxel access points connected to a XS1930-12HP switch. The access points are plugged into the switch via ports 1, 2, and 3. These are configured as trunc ports (tx tagging enabled, pvid=1, management control=1). I have defined 3 VLANS, each mapped to an individual…
-
Question about Throughput
Hello, I have recently purchased a Zyxel XGS1250-12 switch and have the following setup at the moment: My desktop is copying files from the NAS box saturating the 1Gb/s bandwidth. It is not accessing the internet via the router While this is going on, I am on my laptop on a Teams call. I have never had problems before with…
-
LAG working at half speed
I have been trying to set up link aggregation between my PC and NAS via my Zyxel XGS1250-12. My PC has an Asus 10G network card conntected to one of the 10G ports on my switch. My NAS - A Terramaster T5-221 has two 1Gb ports which are connected to ports 5 and 6 on the switch. I have created a bond on the NAS between the…
-
10G Transfer speeds less than direct connection
Hello. I recently purchased a XGS1250-12 managed switch in the home that I could setup my PC and NAS to the router so that all devices are available on the network and have access to the internet. My PC and NAS have a 10G RJ45 port and I plugged the PC and NAS into 10G ports 10 and 11 on the switch. I then transferred an…
-
gs1915 ip setup
I have a GS1915-24 and a 1915-8. Both work very good, but both show this message in the system log (over and over): ER system: Gets the time and date from a time server failed IP configuration looks good to my mind, but the strange thing is, I cannot ping/traceroute any IP address. The switches have static IP addresses and…
-
XS1930 VLAN Trunk, Access, PVID
Hi, I am using my XS1390-10 with a SFP module to access the fibre conneection of my provider. I need to send the VLAN-ID 1120 with the DHCP request. So I configured (in Nebula) my port 10 as follows: Trunk, PVID1120, Allowed VLAN 1120 When I counter-check on the local admin interface of the switch I see the port 10 as…
-
GS2200-24 韌體請求
因忘記密碼，請求GS2200-24 的韌體，謝謝
-
GS1200-8 Firmware update fails
Hello, I just got a GS1200-8 Switch which came with Firmware V2.00(ABME.2)C0 So I wanted to upgrade to the newest 2.00(ABME.3)C0 But this always fails and I get the message that I should just repeat it. I had to downgrade to the .2 Firmware again to get a working device. What did I do wrong?
-
XGS1930-28 LACP vlan configuration
How to configure vlans on a LACP port on the XGS1930-28 ? I can't choose a LACP port in the vlan configuration, only the physical ports (1-28) can be selected.
-
Have my GS1900 switches been hacked?
Some strange things are going on with my Zyxel Switches. A few months back I discovered I could no longer login on my GS1900-8HP. It refused my login/password. I did a factory reset to solve it (and of course put again a custom login/password). Now a few months later its static IP has been changed into a dynamic one and I…
