-
AD Server Authentication fail on the USG Flex 500H if domain name start with a number
ZYXEL usg Flex 500H Firmware V1.21(ABZH.0) | 2024-07-11 06:36:27 i try to join my domain in user authentication / aaa server / ad server summary. Configuration validation check passed with ok but when i try to join AD Domain i can't because my domain name start with a number (!?!?!) my domain is perfectly working and i…
-
Multiple VLAN on single port for Flex 700H
Hi, Does Flex 700H support multiple VLAN on single port? I want to have the default VLAN1 and some other VLANs running on the same port connected to another switch from Flex 700H According to the manual, it say "You cannot configure a VLAN interface and an Ethernet interface on the same port".
-
Admin interface protected by OTP not working after few hours/days
Hi, I have activate Two-factor Authentication for Admin access on my Flex200H (firmware v1.21(ABWV.0). It's working fine, but after few hours or days, when I connect OTP was not asked. If I disable/enable admin Access, OTP was asked again but for few times… This problem exist in previous firmware too. Best regards Luc
-
200H Not possible to disable, edit or remove default global zone forwarder.
200H - firmware 1.21 Why is it not possible to disable, edit or remove default global zone forwarder? System→DNS & DDNS→Global Zone Forwarder
-
USG FLEX 50 (USG20-VPN)
Hello, after resetting the USG, impossible to connect it with IP 192.168.1.1 ping no answer, with Wireshark I see no traffic on the IP 192.168.1.1 Power and SYS leds are green and stable, P2 led is orange and blinking My router DHCP give 192.168.1.1 to the USG, P2 is WAN .. so, I don't know what to do.. I tried with…
-
USG FLEX 200H - URL THREAT FILTER - justid.io
Firewall reports in the threat filter the URL Phishing justid.io to two target addresses 3.225.57.215 3.229.62.193 computers scanned with the best antivirus programs did not detect anything, only WireShark actually shows connection attempts to these addresses. How to solve the problem.
-
new release and HA support
hello when is it supposed to have a new firmware release, enhancing the configuration interface (now very poor compared to the USG/ATP series) and supporting HA as well ? regards Paolo
-
VPN SSL
Can I configure only one SSL VPN access policy on this H FLEX series?
-
VLAN ID on external interface PPPoE - Flex 100H
Does anyone know how to set a VLAN ID on a PPPoE interface type?
-
Why did you do this to virtual interface
USG FLEX 200H V1.21(ABWV.0)ITS-24WK35-0813-240800592 So back when I was testing before V1.2 it was fine I could do: 0 running config# vrf main interface ethernet ge2 ipv4 address 192.168.254.1/29 0 running config#! Commit but now you added this ERROR: [LY] / vrf main interface ethernet ge2 ipv4: Must condition…
-
Frist login after reboot error
V1.21(ABWV.0)ITS-24WK35-0813-240800592 After a reboot I get this error on first login every reboot
-
Is Remote Syslog Server stopping for anyone else? (USG Flex 200 H)
Hi everyone. I seem to be experiencing an issue and wanted to ask if anyone was experiencing the same thing or has ever run into this. I am using the USG Flex 200H device and am trying to reroute its logs to a logging server via Syslog. For some reason, the flow of logs to the remote server will stop randomly after 2-24…
-
ports redirect
hallo everyone, i need to open 2 specific port to my web server. i made this configuration but does'nt work.. what's wrong? i create 2 address object: then the NAT the service and then the security policy but it doesn't work 😅 any help is appreciate !
-
USG FLEX 200H Error Code: [ID:20001]
Out of nowhere after login. Needed reboot.
-
USG FLEX 200H DHCP reserved IP edit error (bug)
USG FLEX 200H, firmware V1.21(ABWV.0) Network Status → DHCP Table When I try to edit reserved IP entry I get the warning: This IP address is not included in the DHCP pool. This happens when editing any field, that is Host Name, IP Address, MAC Address and Description. The workaround is to remove the reserved IP (Unreserve)…
-
Unlocking several portals when using CIP
Hi! I use the built-in Children's Internet Protection policy. I use this policy in education. This is a very nice thing, but I would like to unblock Facebook, YouTube, and Vimeo. The problem with YouTube and Vimeo is that a message related to HSTS appears. I would like to add these two services to exceptions, but I cannot…
-
using two wan ports
hello, is it possible to use 2 wan ports at the same time? hardware used is a USG FLEX 200 idea: one port for the internet second port is for voip each port is connected to a seperate ISP connection.
-
Connectivity Check limitation
USG FLEX 200H V1.21(ABWV.0)ITS-24WK35-0813-240800592 in other models you can have the routeing Connectivity Check ping local interface IP subnet without a gateway and External or Internal but on the FLEX H you can only ping if the interface has a gateway and External. can this be changed thanks
-
Secondary IP addresses on interface problem
USG FLEX 200H V1.21(ABWV.0)ITS-24WK35-0813-240800592 Howto add secondary IP address on interface? — Zyxel Community There is no primary so I have / vrf "main" interface ethernet "ge4" ipv4 address "192.168.255.235/26" / vrf "main" interface ethernet "ge4" ipv4 address "192.168.255.253/26" / vrf "main" interface ethernet…
-
How to set up Link Aggregation group on a USG FLEX 700H
Hei, Received the new firewall and want to setup the 10G ports in a LAG, which connect to the Cisco router/internal network. (LACP) Compared to the UGS FLEX 700, I am unable to locate the LAG setup in the Network→ interface section. Anyone know how to approach this? Mvh, RET