-
At my wits end - iPad roaming Issues
I am at my wits end. I have my NCA5123-NI access points, and one NCA5123-AC-HD, setup with a security profile to use 802.11r. According to Apple, all new iPads support this. I understand that the iPads themselves drop a connection a -70. I have setup my APs, to require a minimum -70 and to drop connections at -75. My Wi-Fi…
-
ZyMesh Question
Hi All, I am trying to understand ZyMesh a little better and I am looking for some help. I have 5 APs in my environment and a NXC2500 controller. They are all connected to my LAN via Ethernet, all using same SSID and security profile. Recently, I have been having some issues with devices connecting to I have been…
-
Problems with Windows 10 Clients
We are using the following items: - USG 210 - WAC6503D-S - WAC6103D-I - GS1900-10HP All AP's are configured the same way. Everything works fine for all Android and Apple Clients. But if we have Clients using Windows 10 (phone, tablet, laptop) then the WLAN connection is also established but all of these clients do not have…
-
NXC 2500 " Wrong CLI command" after Login...
After Login on the NXC 2500, " Wrong CLI command" pops up on every point of the menu. a restart has no effekt.... any ideas ?
-
Purchase a second AP
Hello. I have a NWA1123-AC in a rather small room, and then I have another room next to this room. This room has a door but the rooms are separated with very thick walls. Because of the thick walls the wifi signal is too low in room 2. So I am thinking of getting another AP. But I would like to use the same ssid so that…
-
Count licenses
Hello
I have purchased and connected two new NWA5123-AC to my NXC2500.
They do not seem to work but appear in the NXC2500 and appear to be properly connected.
I'm not sure how many licenses we have installed.
Where can you see how many licenses are installed?
Sincerely
Bengt Jönsson
-
Update firmware version help
Hi I would like to ask if there is a new version of firmware for my Zyxel modem? The model is ZYXEL AMG1302-T10D mypldt dsl is the network provider im in philippines...
-
NWA1123-AC HD - unable to access after any changes
NWA1123-AC HD PRO - trying to set this up. I am connected to my home network - making a few settings before setting up at work. If I try to change the basic ssid password - it is then impossible to connect to via wi fi. In fact the router is then impossible to connect to - period - even via a direct cable connection. I was…
-
How can I add a Wifi device which only supports WPS?
Hi, I have a business network with WAC6103D-I and NWA5123-AC. These accesspoint are managed with the USG60. I have wifi printer which supports only Wifi WPS configuration. How can I add these printers into the wifi?
-
NWA1123 Password After FW Update
I have just completed the firmware update to V211AAEO0C0 on my NWA1123-NI. Upon completion the AP seems to be working fine (SSIDs still broadcast and connectable). However, I tried to log back in to the AP using the default password of 1234 and cannot log in. I then attempted to log in using the password that I had set on…
-
Is there any way on controller to disconnect a station?
Is it possible for a client (station) forcing the controller to forcibly log out the client (station)?
-
NXC Master and Slave sync.
The NXC Master and Slave devices should be synchronized about the configuration and dynamic guest account.
-
WAC5302D-S: Managed mode support
Hello, this message is dedicated directly to Zyxel support staff. Please I need information about support for WAC5320S-D in managed mode. I know that this access point can operate in managed mode (Device user's guide WAC5302D-S_V5.00.pdf). I am trying to connect USG60W (AP Controller) with WAC5302D-S (Managed AP) without…
-
What is the maximum of managed APs for NXC if I buy the license?
Hi, What is the maximum of managed APs for NXC if I buy the license? I would like to know the information about NXC2500 and NXC5500.
-
The managed AP has to do time sync by CAPWAP with NXC,only NXC has to do NTP sync.
Within managed mode the AP has to do time sync by CAPWAP with NXC., only NXC has to do NTP sync. The AP does now try to sync. NTP at boot and every 24hours. Imaging the point you have 500 APs deployed in the Network and each single AP has to do its own NTP sync.Currently Ap will get NTP time from AC if we set up the AC as…
-
Hope NXC support USB storage for Wireless Frame Capture.
For troubleshooting in specific customer environment we require to record Wireless Frame capture for several Monitor AP during 2-3 days. As this is creating some amount of data we liked to use USB storage for Wireless Frame Capture Option but disappointing the USB storage only Support for "normal" wire capture. IK
-
How can I release IPs from the DHCP pool on NXC5200?
Hi, I use NXC5200 as my DHCP server, but the DHCP pool is full now. The new clients cannot get IP but there have too many redundant users, how can I release them???
-
NXC2500 Firmware 4.22. to 5.10
hi there, may i update Firmware from NXC2500 V4.22(AAIG.1) directly to NXC2500_5.10(KRACK_hotfix)? (all APs are NWA3560-N) thx
-
DOES USG210 supports different brand Access points
hello , i want to know does USG-210 supports different brands of AP if used as controller.
-
DOES USG-210 supports different brands of Access points
i want to know does USG-210 supports AP's of different brands if used as controller.