-
[New Release] True WiFi 6 - Zyxel NBG7510 AX1800 Gigabit Router
https://www.youtube.com/watch?v=NHavSZtz7PI
Say goodbye to the out-of-date router, meet our
new ultra-high-speed and the best value AX1800 router－NBG7510.
Zyxel brings NBG7510 new entry-level WiFi 6 router, loaded the latest AX
technology helps focus signal strength towards your devices, significantly improve the…
-
I need an external antenna for my VMG4927-B50A modem
This discussion was created from comments split from: Zyxel Community Guidelines.
-
Does ZYXEL EX3301-T0 support WPA-PSK for older WiFi printers?
My WiFi printer does not support WPA2-PSK. Does the EX3301-T0 support WPA-PSK? Thanks!
-
ZYXEL FWA710
Hi, I recently posted on here regarding this Router , but decided to purchase one to replace a not very weathertight ZTE MC 7010 which works well I get around 200 mbs with it using 5g , my 5g phone can manage up to 300mbs at the same spot, the replacement FWA710 seems very lacklustre and is slower in general at around…
-
How to configure DX3301-T0 to send daily logs?
I can't seem to find where to set up scheduling an email containing the log files on a daily basis. This was a facility in my old Zyxel (AMG1302-T10B) and it was useful for keeping an eye on what was going on. Can someone point me at the equivalent part of the config screens for the DX3301 please? I've set up the relevant…
-
Use network ports on WX5600 while in RP mode
Hello, I'm considering buying a WX5600 - is it possible to connect a non-wifi device or a switch to a WX5600 via cable while its in repeater mode? I haven't seen this scenario covered in the documentation. Thanks for your help. Regards, Sebastian
-
How to enable port forwarding on ZYXEL DX3301-T1?
Hello everyone! I have this issue, how can I set a port forwarding rule? I tried to search on the internet for my correspective model but I can only find the "DX3301-T0" one… How is it possible? On my zyxel there is no port forwarding option… I only have firewall's section that has ACL and Protocols rules only…. Can anyone…
-
Firewall
I have recently starting using a Zyxel DX3301-T0 router, after using a Draytek for many years. I use Norton 360, and yesterday, during a scan, it reported 'Device is accessible from the internet' and urged me to use the Norton VPN. I tried this, but Ebay would not work with it. I then changed the routers firewall from…
-
2 apartment NAT
Hi I have a NBG6817 with 1 incomming etherne connection. Can I use this router to split the one connection to 2 different appartments and make 2 differenta LAN/NAT so that they dont have access to eachother at all? And i so how? What settings?
-
EX7710-B0 Firmware Request
Currently running V5.18(ACAK.0)C0 but need to upgrade to V5.18(ACAK.1)C1 to address a few vulnerabilities. Where can I get firmware?
-
MPro Mesh App Parental Controls Bug
I have a MPro Mesh App to control my Trooli FTTP EX5601/EX5600-T Router. Which is all running well on 26 devices but as soon as I try and link my Sons Meta Quest 3 to lock down the hours it selects another device on my list. This can be at random but it just doesn’t seem to want to add the Meta Quest 3 to the group. As…
-
default credential not accepting in Zyxel P-2301R-P1C
@Zyxel_CSO After resetting my Zyxel model (Zyxel P-2301R-P1C) default credential is not taking. we are getting default ip as 192.168.105.1 and we had tried all possibility. Could someone please help me on this.
-
Firmware for Zyxel MWR102
Hello, I purchased my Zyxel MWR102 in 2014 for travel. I want to update the firmware, but couldn't find one in Zyxel download library for this model. Would you please help me with this? the current firmware is v2.04r1
-
FWA510 loses PIN on reboot
Every time I reboot my FWA510 the PIN for my SIM-card is lost and I have to logon to the router and re-enter the PIN. Does anyone have suggestions as to how I get it to remember the PIN? At the screen where I enter the PIN, it states, that the PIN is automaticly saved in the device, but I clearly doesn't.
-
FirmWare for SBG3310-A
Can anybody share the latest firmware for SBG3310-A? I can't find it anywhere. I reseted the device to defaults and now it asks online firmware upgrade during setup wizard. I can't configure anything without resolving the initial wizard. Does anybody know how to avoid configuring the device without the wizard?
-
Zyxel SBG3310-A software
Hello! I have SBG3310-A gateway. It is absolutely new(many years in the box on the shelf). Now I decited to use it. But I tryed to gonfugure it and I faced with the initial wizard. System checks it in cloud resources and can' t find anything. Also it wants new firmware, which I can't find. Tell me please, how can I skip…
-
EX5601-T0 Connectivity Tab Bug? (F/W V5.70(ACDZ.2)C0)
Another bug/issue on the EX5601-T0 F/W V5.70(ACDZ.2)C0 Can't find any references to a known issue or firmware update On the Connectivity widget on the home screen If I select this widget I don't have any devices listed: Is this a known bug / issue and if so, when is a firmware update planned. Thanks
-
Service problems - using ARMOR series
Someone know why? Connected using WIFI, and same with LAN directly, seems to be an issue when trying tro access LOCAL WEB GUI, but is there a bug with this cause its also connected to the cloud? Any Cloud issues - for these consumer products? Is there MORE info we can get out of this BOX like NVRAM errors? or other logs…
-
Zyxel vmg3925-b10b default password
I have reset my vmg3925-b10b router to use as a backup, but am now unable to login. I have tried the suggested options of admin with 1234, password or admin, but they don't work. My original password also does not work now. Is this now bricked or are there alternative methods of regaining access to configure it?
-
EX5401-B1 guest network
I have a Zyxel EX5401-B1 router and am looking to make a printer on the internal network available to the guest network for the occasional printout. Is this possible with the router interface? I've looked at the port forwarding, but this seems to work only with the external interfaces, address mapping seems to do the same…
-
WX3100 not visible in MPro app after successful connection
Situation: AX7501 Router with one wired WX3100 in the parent bedroom as a mesh device. I want to add a second Wifi-connected WX3100 to extend the mesh to the kids bedroom. In the living room, close to the AX7501, I add the second WX3100 using the Mpro app via the "Use WiFi" option. I press the WPS button on the WX3100, and…
