-
UAG4100 - User disconnected automatically after 3 minutes
Hello community, I've a problem with my hotel WLAN. Guests who have logged in with a web access (username, password) and successfully connected to the internet are automatically logged out again after approx. 3 minutes. They can then log in again and access the Internet again.What settings need to be made so that this no…
-
VPN Policy Route on NSG 100
Hi I am testing VPN connections between USG FLEX 100 and NSG 100 since USG FLEX is the new version of NSG.My problem is that I cannot select VPN when I want to create a Policy Route on NSG, VPN is greyed out. What do I do to be able to create a Policy Route for traffic that will use the VPN connection? RegardsOlav
-
Small interface type bug with general on boot up to SNAT traffic
V4.72(AAAA.0)ITS-22WK28-r104687 In order for the Zyxel
devices to connect to the internet they must use VLAN443 and SNAT to
OPT Normally the VLAN443
would be set to external but changed to general for testing DHCP On rebooting the USG40
and Zywall 110 I found the USG40 on service license refresh failed
but Zywall 110…
-
Apply config file from Zyxel USG40w on USG60w
Hi there, We are running a bunch of Zyxel USG40w and we have our standard configuration file for them. We have to deploy new Zyxel devices at a very far remote location where they can only get USG60w devices. Would it be possible to apply the 40w config file on those devices ? Thanks for your valuable inputs. PG
-
USG20W-VPN Firmware Upgrade Path from v4.33 to 5.31
Hello All, When we get our USG20W-VPN units, they arrive with 4.33 firmware on them, so we have to upgrade them to 5.31 before shipping out to customers. My question is what is the most efficient upgrade path to get from 4.33 to 5.31 without going too far to where it may impact the unit by jumping too many at a time?…
-
ATP200-to-ATP200 VPN Connected But Cannot Access Resources
First post on this forum. I did multiple searches before posting. I have two ATP200's connected with a wizard-created site-to-site VPN. Both devices show the VPN as connected with a green globe. Site 1 LAN: 192.168.0.1/22 Site 2 LAN: 172.18.10.1/24 From site 1, I cannot ping any known 172.18.10.x address or access any of…
-
ZyWall 110 Legit Virus or not?
Hello, I've received 2 reports in a week of a virus on one of the endpoint devices on our network. One a Mac and one a Windows Workstation. Virus infected Rule_id=8 SSI=N Virus=CB
Wildcore.Virus.4a4ec363
File=QiH9IvwJQIOdiJz7838GXHQ0+oHQxzX4PGdBUE4ensIwNH5YBXZpODpsmI0O1
Protocol=HTTP Does anyone know if this is a false…
-
Zyxel USG 100 - can't access with latest browsers - unsupported protocol
I have an old USG 100 in production and when I try to sign in from Microsoft Edge I get an error. Unsupported protocolThe client and server don't support a common SSL protocol version or cipher suite. I think this might be a lack of support on the USG for TLS1.2. What can be done??
-
failed login OID SNMP
Hi, is there a possibility to track failed login attempts using SNMP ?? Or just login to device (USG 60 eg.) ??
-
Firmware USG 100
hello I am looking for a newer firmware for an old usg 100.Does anyone have this available? current installed Version 2.2(AQQ.0) from 2010.
-
Unable to open port /NAT on USG40W
I have followed both of these guide to a "T" and my USG40W refuses to port forward: https://mysupport.zyxel.com/hc/en-us/articles/360003880919--ZyWALL-USG- How-to-open-ports-on-a-ZyWALL-USG-router-Port-Forwarding-NAT- https://support.zyxel.eu/hc/en-us/articles/360001390934-NAT-Rule-Configuration-on-a-USG-Port-Forwarding- I…
-
How do you change a device status to 'Inactive' on MyZyxel?
Greetings, I am trying to figure out how to change a particular device's status to 'Inactive' while it is in the process of an RMA. It hasn't been connected to the network for about a week now, and yet it still shows as 'Active', even though we have replaced it and the new USG60 is showing as 'Active' as well. I am hoping…
-
Security Advisory for firewalls published 19 july
https://www.zyxel.com/support/Zyxel-security-advisory-authenticated-directory-traversal-vulnerabilities-of-firewalls.shtmlwithout the damned link to wk28 file. The way Zyxel is managing this occurrencies keep looking bad, uncomplete and unsatisfying.
-
SSL VPN Secuextender and MacOS 13 Ventura
SecuExtender for MacOS the latest version is 1.2.4.1 and it support MacOS 12.3 MacOS 13 may have compatibility issue between SecuExtender 1.2.4.1. We will release new version at 2022Q4. Please do not upgrade your MacOS to 13 before new SecuExtender is released. Or you can use L2TP/IKEv2 VPN tunnel as backup solution.…
-
Wan2 on usg60w
I changed my Wan2 provider previously configured with PPPOE account, and working as failover. Now, with new provider, I don't have any pppoe credentials, and the wan2 connection doesn't work anymore (i simply connect wan2 port to my modem/router). How must I configure the wan2 connection? Do I need to remove the isp…
-
Timeout reaching category filter
Since this morning i noticed that my USG300 is unable to reach category filter and every query get a TIMEOUT message. It's a known issue common to everyone or my internet provider did something wrong with the upper firewall? Does anyone knows the address(es) of the category filter so that i can check if the server can be…
-
SecuExtender inconsystent connecting to USG FLEX 200
I the past few months we noticed inconsistency connecting SSL_VPN to USG FLEX 200.Sometimes is connecting sometimes not. Have the same VPN configuration for a long time and have been using it for years. Installed the latest firmware and running Secuextender 4.0.4.0 last night I got connected but this morning cannot. I'm…
-
ZyWall 110 to USG Flex 500 Upgrade - possible?
I have a ZyWall 110 and would like to upgrade the firmware to USG Flex 500 to enjoy further features. Is this possible? or do I need to discard the ZyWall 110 and buy a new HW platform?Thanks
-
Limitar banda por ip
Srs bom dia, existe uma possibilidade de limite de banda (internet) por ip no firewall USG110 Zyxel? se sim, como? Good morning, is there a possibility of bandwidth limit (internet) per ip on the USG110 Zyxel firewall? if yes, how?
-
USG210 as AP controller access local network
I have a USG210 as AP controller. See below. Please, can anybody tell me how I have to setup the USG210, so I can access the fileserver with the laptop.
