-
GS1900 24HP - Configure VLAN and LAG interface
Hello ! I was given this switch for Christmas and, as I'm still a networking student, I haven't mastered everything, so I could really use your help. Here's my architecture: OPNSense (Port 1/LAN) → SG1900 (Port 1) OPNSense (Ports 3&4) → SG1900 (Ports 23&24) SG1900 (Port 9) → PC (DHCP Enabled) I wanted to make sure that…
-
Switch GS1920-24 where to find saved configuration?
When I press the button at top/righthandside "SAVE", it says after showing a progressbar: "Save configuration successfully." But neither a file into the win10 Downloads folder was saved, nor a dialog to ask me where to save it appeared. Where can I find now the saved config file?
-
EEE / Green Ethernet
Hi If I use a switch like GS1915-8 in Nebula-mode, I can't control EEE/Green Ethernet. Will it be enabled or disabled by default in NEbula mode?
-
Internet radio buffers forever: IGMP problems?
I have a Magenta TV receiver from Deutsche Telekom that requires IGMP. Now I have the effect that when the receiver is running, regardless of whether a channel is being watched at that moment or a program is being recorded in its absence, the Internet radio in the bathroom buffers for seconds, then plays a radio program…
-
Doubling the bandwidth of the link between switches series1920
Dear all, I based the network backbone on zyxel1920 switches. Due to the high load on the network, is it possible to double the bandwidth by connecting two switches using two parallel 1GBps links? (where to look for such a configuration). Is it possible to configure a network with a ring on these switches (each switch…
-
Static LAG VLAN membership
Hi there! I have a brand new XMG1915-18EP switch. I have 3 VLANS, users, guests and IoT. I set the port 17 and 18 as a static LAG with source and destination IP address protocol to another switch. I want to do the following setup: user vlan: untagged ports 11-15 and tagged on lag guests vlan: untagged port 16 and tagged on…
-
Correct Port Settings for a Sky Q box?
Hi! Wondered if anyone could help. I have a small home network, with a sky router connected to the phone line giving me 35Mbps broadband speed (no fibre here!). The Wi-Fi on this router is switched off. I then have two GS1915 switches and two NWA50AX WAPs providing Wi-Fi coverage around my house, and hardwired connections…
-
need Help for XGS4700-48F bottloop
Hello Community, our XGS4700-48F is in a booting loop. I think they forgot the default config. I´ve tested many time to send my config and Firmeare via Xmodem to the device. evrytime i get the Error "Received file size Error" Have any one an idea? Thanks for answers.
-
XMG1915-10EP - POE / PD is interrupted when booting
Hi, I have noticed, that switch when booting is performing 2 or 3 restarts of POE (power delivery is interrupted and resumed). I would like to ask - is there any way to avoid such a situation? This is unfortunately causing that some of my SBCs etc. devices are powered up and forcibly powered off, then powered up, and…
-
GS1200-8 Webinterface behind nginx reverse proxy
I'm running a local nginx reverse proxy as gateway between my home network and the management network. The switch webinterface is reachable from the management network, the Idea is to use nginx to have secure access to the switches webinterface from the home network. This is my nginx config: #/etc/nginx/conf.d/switch.conf;…
-
GS1200-8 vlan behavior on incoming tagged frames
Hello. I want to buy the device in the title. Before that I would appreciate it if someone could help me understand the following expected behavior: If I configure for example port 1 and 5 with vpid 10 and port 2 and 6 with vpid 20, it is my understanding that when a host connected to one of those ports sends an untagged…
-
How to exit from SSH session on GS1900-8HP?
'exit' command does nothing. logout, quit, … are not valid commands. Switch revisions A1 and B1. Latest firmware installed: V2.80(AAHI.0)C0
-
Slow connection between VLANs on GS1915-24E
When I try to move a file from a Computer located on lan1 (port3 on the switch) to a NAS located on VLAN20 (port23 on the switch) the connection is very slow. I would say it's like 45% of max possible. If the Computer is on the same VLAN everything works fine. Speed is at max level. I was using a TP-Link switch before that…
-
Sloooow CLI
Hi I am using a XS1930-12HP with the L3 license. I have Cisco and Netgear prosafe switches and use CLI most of the time. The switch works well. This is just a comment to zyxel staff… I must say the CLI on this Zyxel is really slow. Just show running-config takes 3-4 sec of thinking before rolling up on screen. My old…
-
ZynOS wont accept DNS names in some syntax
Hi It seems ZynOS V4.80(ABQF.4) | 08/23/2024 support to use a DNS name in the "timesync server" command but not in "syslog server". I hereby ask you Zyxel staff for a future update as there is actually no reason at all to not allow a dns name in the "syslog server" command as well. Hard code IP:s where there is no need for…
-
Compatibility Problem Solved with V4.80(ABQE.4) firmware
I just wanted to let folks know that I encountered what looked like major incompatibility issues with me pair of XS1930-10 switch whilst running the V4.80(ABQE.3) firmware. For example, my Draytek, Netgear and Technicolour managed switches and routers along with unmanaged switches could not be detected when plugged into…
-
GS1920-48 from 4.50 to 4.70
Hello, I have GS1920-48v2 and upgraded to V4.50(AANZ.3) how to upgrade to 4.70(ABMJ.4)C0 for example. I can't find 4.60 on the site. Kind Regards, Stoyan
-
[GS1900-24EP] Having Wireguard Subnet be on same subnet as LAN
Hello everyone, My use case is that I have two devices that need to be on the same subnet. I am using software called Dante Controller that only works if all clients are on the same subnet. The issue is one device is attached to the network via Wireguard VPN and, therefore, on a different subnet. The two devices: 1. An…
-
XGSXGS1930-52 IP-Settings
Hi, We have 2 XGS1930-52 switches. I have installed the new firmware version V4.70(ABHU.9) 11/04/2024 on the switch. The switch is assigned an IP address via DHCP. However, it is not possible for me to change the IP address from DHCP to a static IP address under IP interface. I get an error message every time, even though…
-
Disable sending LLDP to ISP over fiber link
Hi Sorry for my intensive posting. I am new on modern Zyxel switches and syntax differs a little bit against what I am used to :) Trying to make sure the new Zyxel switch will do what I expect it to before make it production active. Instead of doing this on the fiber port interface to the ISP… no lldp basic-tlv…
