-
GS2210-24 jumbo frame
How to enable jumbo frame?
-
how to get firmware updates for NR7101
Hello, I am new here. I am just installing a NR7101 here in France, and I am trying to make sure the firmware is up to date, but I am not sure how to check. in myZixel I see this message and I can't find where the "configuration" area is to do what the popup suggests. I checked everywhere and can't find it. my 5G…
-
Is it Zyxel GS1920
* Is it Zyxel GS1920? Is it Zyxel Firewall model?
-
GS1920-8HP can't set time
I can't set time on GS1920-8HP V4.70(ABKZ.7). After changing "New Time (hh:mm:ss)" and "New Date (yyyy-mm-dd)" and "Apply" - they returns to previous values. -- Solved
-
considering buying XGS1250-12 and I can see that it can work with max 12kb jumbo frames
considering buying XGS1250-12 and I can see that it can work with max 12kb jumbo frames.
-
Mixing Speed Compatibility 2.5Gbps <--> 1 Gbps XS1930-10, XS1930-12HP or XGS1210-12
Hi Support Zyxel and community, I decided to upgrade to APs coming with a 2.5Gbps port just to find that some switches do not like or fully support this configuration, 2.5Gbps <--> 1Gbps with or without flow control. Basically, every time I have a 2.5Gbps AP port communicating to a 1 Gbps device the max upload speed from…
-
XS1930-10 - electronics noise
Hi Zyxel
Support and community, I am
evaluating XS1930-10 and this device is quite unique and meets most my needs
except one area ... noise. I can accept noise level when fan spins around
minimal RPM (3500), but my problem starts when temperature raises. I have
noticed then strange clicking / rattling sound. It occurs only…
-
GS1005HP are POE ports active or pasive
I want to feed an expensive sound amplfier with data to its Digital converter through a POE port. I understand if the POE is active and there is no demand of electric power from the amplifier, the port will not send also electricity but only data, so there is no risk of damage. But if it is passive it might deliver power…
-
Have xgs1930 switch. Make changes via either GUI or Wizard. When I do config backup, changes are n
Have xgs1930 switch. Make changes via either GUI or Wizard. When I do config backup, changes are NOT reflected in backup config. Also within SSH connection, show running-config' does not display any of the changes. Am I able to gain CLI access to make config changes? Why do GUI changes not show in running config?
-
Accessing my printer from another VLAN
I have a UnRaid server that is also hosting my Windows VM, which is using VLAN ID 10. My VM can freely access all other devices on the network, however, I am having trouble connecting to the printer. If I want my VM to access the printer, should I configure Port5 of GS1200-8 as tagged or untagged for VLAN 10? Since the…
-
GS108S needs hard reboot after power-outage
Getting a lot of mains power cuts here (Hampshire, UK) recently, which has reminded me of a problem I have seen before and that keeps recurring. Each time power is lost, part of my LAN can't see the router that connects me to my VDSL service, so all Internet connectivity is lost for that part of the house. The solution…
-
is it possible to upgrade firmware v2.20 direct to v2.60 gs1900-24e
Or do i have to install the previous version first? Thanks in advance Mick
-
Establishing VLANs
Hi, I’ve recently purchased a GS1200-5. I have an IoT device which I want to only have access to the internet, not the rest of my LAN. my current set up: - wireless router (built-in modem). majority of devices connect with wifi, however my NAS is Ethernet enabled. - Zyxel switch, Ethernet from router to port 1. I tried…
-
Configure RSTP
I would like to ask about spanning-tree settings on MES3500-24 switches. What is the best way to configure the RSTP version? What is the difference between no spanning-tree 25 edge-port and spanning-tree 25 commands
-
XGS1250-12 loses LAG config after restart
My XGS1250-12 has a LAG setup to a GS1900-24E. After restarting it seems as if no traffic flows through the LAG because I lose connection to devices on the GS1900. When I log into the XGS, the LAG appears to be configured. However, if I click Apply, the LAG then drops out of VLAN1 and I have to add it back as a member of…
-
GS1900-24EP-EU0101F
Guys, I can see in specification, that my switch "GS1900-24EP-EU0101F 24xGbE L2 12xPoE Rack 130W" is manageable one. However, couldn't pair with Nebula Control Center (NCC). Apparently, also manually could not link it via MAC&S/N. Cannot find info about incompatibility with NCC. Thanks for advice.
-
lockout
Hi guys We have some switches (e.g. GS2210). Some of them are not accessable on some servers. Is there the possiblity to see if some IPs are banned to login from? It is really annoying because I have to switch from server to server until I found one from which I can login (all in the same subnet and vlan). I tried it with…
-
Gs1920-hp48
Hi and thanks in advance . I have a problem with my gs1920hp48. the 192.168.1.1 wont open in edge or explorer. comes up with connection error. i updated the firmware this it when it happened any help would be great
-
XGS1930 ftp firmware update
How can update firmware from ftp command line?
-
GS1900-24E doesn't store config
Hello, I am facing a serious problem with one of my GS1900-24E. I can configure the switch via web-gui and the values are stored in the running config. But if I reboot the switch, it looses all its config. What I tried so far: - set the switch to factory default via web-gui -> still same behavior - set the switch to…