-
When was DCS added to the NWA1123-AC Pro firmware
I thought for sure I had setup my access points with a fixed channel but recently notices they were set to dynamic channel selection. Was this a fairly recent firmware addition or has it been around a long time. #Biz_WLAN_Dec_2018
-
Is it possible to set the automatic restart of the device once in a week or month...
At many of our installs, we are facing issue with lower speed, delay in getting IP for the new connected device and it is resolved once the controller is restarted.
-
my GS2210-8HP lost the PoE function over night
Hi I use my GS2210-8HP to power two NWA1123-AC-Pro and over night the power was gone. If I inject the power via an extenal PoE power supply everything works perfekt. I switched ports but I got the save effect. Any idea what can cause the problem? many thanks Kind Regards alex #Biz_Switch_Dec_2018
-
AP NWA1123-ACV2 Uplink port randomly down and up
Hello to everybody, this is my first message on this forum. I own a Zyxel NWA1123-ACV2 from some months, configured as standalone AP, connected to a Netgear GS108E-v3 switch. I noticed from several days that uplink port sometimes goes down and then up after few seconds. Sometimes it happens every hour, or every 20 minutes,…
-
Reconfiguring NXCS2500 and USG60 after USG60 reset
Hi all, I'm pretty new to Zyxel products so I might miss some important information, hope you will excuse myself (and my english). Here is my question : one of our customer had the following setup, which was installed by another company. The thing is that our customer stopped working with that company due to some conflicts…
-
How to setup a WLAN and configure devices as repeaters to expand the wifi coverage across building
Hi, We would like to set up a local Wireless LAN, and expand across our building the Wi-Fi coverage with devices acting as repeaters. Please find below our requirements: The building has 3 floors (ground, 1st and 2nd). - On ground floor, we have installed one ZyXEL with the hostname "Slave 01" with a local static IP:…
-
Zyxel NXC 5200 5Ghz
Hi, There is a NXC5200 controller, there are access points at 2.4 GHz / 5 GHz and a few at only 2.4 GHz. The problem is this: the client connected to the 5 GHz point when moving to a zone where only 2.4 GHz the client does not automatically connect to the 2.4 GHz network.
-
New german initial draft for rules on securing Small Office and Home Office
Hi guys Documentation. The German government published at the start of the month an initial draft for rules on securing Small Office and Home Office (SOHO) routers.Published by the German Federal Office for Information Security (BSI), the rules have been put together with input from router vendors, German telecoms, and the…
-
Broadcast (storm) Problem WAC5302D-S
Hello guys, were using an NXC5500 with multiple Zyxel APs in an enterprise enviroment. Only the WAC5302DS APs get stuck random. The only maybe problematic thing i can diagnostic is that on any WACs RX side are big Values of broadcast pakets while all the other non WAC aps are stable and have very low BC rates. How could…
-
NWA1123-ACv2 Guest access only internet
Hi, how can I configure a guest access only with internet access ? thanks #Biz_WLAN_Oct_2018
-
Can I use Zyxel NWA3560-N as a range extender for wifi network
Hi, I have a NWA3560-N but for now it's useless for me, as I dont know if I can use it for extend coverage of wifi network in my house. Is it possible with this? #Biz_WLAN_Oct_2018
-
Multiples VLAN behind unique SSID - 802.1x
Hi everyone, We are using NWA5123-AC-HD, VPN300 and Windows NPS as radius. Is there any way to configure multiples VLANs behind one SSID ? The idea is that the VLAN assignment will be ruled by NPS. So all users connect to the same SSID, but then get access to their own VLAN, depending on their LDAP group. Regards,
-
LTE4506-M606 - Webinterface - unable to enter "username"
Hello! When trying to log in to the webinterface of my LTE4506-M606 it is not possible to enter a username, the field is blank and not accessible. It is not possible to loging, because of a missing username. How can I enter a username in the field "username". BR Jochen
-
NWA1123-ACv2 local managment not full version
Hello why my local management isn't basic and not full? see the screenshot #Biz_WLAN_Oct_2018
-
Nwa3560-n upgrade
I am a very small business, three NWA3560-N WAPs currently, one site. I am thinking about upgrading to top of the range rf performance, 802.11ac wave 2 MU-MIMO. Very low client density, but very high throughout wanted, seamless roaming and top compatibility with Apple iOS. Which products do I need to look at? I must admit,…
-
Set up a NWA1121-NI as a second AP
Hi What is a simple way to set up a NWA1121-NI access point to extend my broadband into the garage. I have tried to set this up but the internet will not connect. Thanks Koops #Biz_WLAN_Oct_2018
-
Zyxel NXC-5200 Flash full
Hi, I took over a Zyxel NXC-5200 controller from a client his ex partner. I have 2 issues: 1) Flash is full, so I reboot and lose all my chances :( 2) I can connect to my new 2016 AD domain and can read user Attr, but when I configure an SSID with that profile he says that he cannot connect to that network. I followed the…
-
AP Zyxel NWA5123AC issue
I am using 2 AP Zyxel, printer and desktop connect to using wifi. the issue when I'm trying to ping from desktop use wired connection to desktop or printer using wifi connection it has a lot of requests timed out. I checked the configuration and connection between the Firewall, switch, and AP looks normal and I can ping…
-
2.4G and 5G leds remain amber on my Zyxel nwa1123-ac pro even after correct configuration
Hi, so I've configured my zyxel nwa1123-ac pro and it works just fine, absolutely no problem 'till now. Only thing is, the 2.4G led and the 5G led remain amber(instead of green) and I don't understand why, since it works. I know it might seem trivial, but I would like to know if maybe I've missed something. Thanks
-
VMG8924-B10A - Can't connect to WLAN / Happens Occasionally
Hello, Our router doesn't accept wlan connections time to time, even i turn wlan off/on again from panel it's still same. If i power off and on it starts working again, but after a couple of days it's doing same thing. Installed firmware: 1.00(AAKL.21)C0 I have also called Zyxell Turkey and they have connected to my pc,…
