-
Wifi controller migration
Hi all, I’m migrating Wi‑Fi management from an ATP200 to a USG FLEX 700H (FW version V1.35(ABZI.1)) however I am facing some issues. The problem is that I am not able to register the APs on the FLEX. When I remove one of the APs from ATP200 management by clicking on the Remove button (so far I removed just the one since I…
-
NWA130BE - "deauthenticated by key handshake fail" with certain devices
For some strange reason only all of our Raspberry Pi Zero 2W can't connect due to the "deauthenticated by key handshake fail" error. Also log shows "left on […] Signal: -16dBm" which I've never seen even when the device (as in this case) sits in 1-2 meter range of the AP. I tried the usual stuff changing channels, rate…
-
Macbook and iPhone disconnects - NWA50AX
Good morning everyone, I have a couple of NWA50AX and always have trouble with Macbooks and iPhones. I have a lot of disconnects even though I'm pretty close to the AP. All other devices: Windows, Android and large amount of Shelly devices do not have that problem. Any idea if there are any settings that would help me?…
-
NWA50 AX PRO: stuck on wizard message.
I received 3 NWA50 AX Pro devices. They are going to replace other devices, so I have a compliant configuration file for the hardware, based on a 7.10.(3) firmware for the same device. All three devices serials start with "S250Y0". Windows as OS, Firefox updated as browser, Sophos as AV. First access, DHCP configuration,…
-
FWA505 openvpn
Hi, I possible to connect my FWA505 to a openvpn server? The server is working good and is somewhere in the internet, not in my local network. I do not found any config page about VPN at my device admin page (192.168.1,1) At the moment I have not activated Nebula. Thanks Max
-
My NWA50AX keeps losing link on the LAN port
Hi, I'm running a NWA50AX via Nebula over POE. It's an unmanaged Zyxel switch on the other side. The AP keeps losing the link intermittently. Anything I can do to diagnose what might be the issue? Thanks
-
NW55AXE Access Point Nebula Internet Access Issue
I connected my access point to a port on the switch that I set as untagged 100. In Nebula, I set the VLAN ID as 100 in the SSID settings. In the SSID advanced settings, I set the VLAN ID to 701. In the AP & port settings, on LAN 1, I set PVID to 701 and Allowed VLANs to 10, 20, 100. My access points appear online in…
-
700H wireless. How to I adjust each AP transmitter power?
Looking for: "Overwrite Group Output Power Setting" for a given AP. Heat mapping our 6th floor and I need to turn down that AP's transmit power. On the USG 700 is was easy, you clicked on the AP in the "Mgt. AP List" to adjust it. How do I the same thing on the 700H?
-
NWA1123ACv3 Energy bursts accross 2.4GHz channel 1 and 11
Hello Support, Please can you tell me if this is normal behaviour? The image shows a scan from the 2.400GHz to 2.433GHz, channel 1, taken from my TinySA Ultra+. I've isolated it to the wireless router and bursts change as I change channels. I get the same high energy bursts on channel 11. It is not continuous but changes…
-
WBE660S: 1-2 reboots per day with 7.20
Hi all, i updated my WBE660S to 7.20. Since that i see 1-2 reboots per day (Log: Device is rebooted by kernel panic!). I saw this reboots in the past with enabled MLO, after disabling the AP runs perfect. Can i disable MLO in 7.20? The button is gone because of implementing Wifi7 at all. Regards Christian @Zyxel: I allow…
-
NXA130BE - boot loop since Firmware 7.20 when Iphone16pro in 6E automatic mode
I did the update to Firmware 7.20. Now my NXA130BE goes into a boot loop when I switch my Iphone 16Pro into 6E "automatic mode". When I switch it to 6E "off" everthying is allright.
-
NWA110BE and DFS on a Sonos Move 2
I recently switched my WAP to a NWA110BE, and while all my other devices seem to have no problem, my Sonos Move 2 won't connect when I'm on the DFS channels. I live in an area with very crowded spectrum, so I do a lot better on DFS and there is no radar in my area. Any ideas on what changes I could make to get the Move 2…
-
[HOTFIX] Resolve Wi-Fi 7 AP Unexpected Reboot Problem After 7.20p1 Upgrade
This discussion has been moved.
-
Remote site with 5G access
hi, I have a USG FLEX100, with several VLANs configured. I will need a 5G Wifi router on a remote site and want to add a site to site VPN to that router, so that I can extend some of the VLANs to that site. I have two questions: Which Wifi products support this, or are there any. For example, does FWA510 support…
-
wifi ne fonctionne plus depuis la MAJ
Bonjour je vous contacte suite a de gros problème de wifi depuis votre mise à jour sur les point accès wifi 6 et 7 . J utilise deux bornes wifi : NWA130BE et NWA50AX depuis cette MAJ le wifi est instable voir inutilisable aussi bien en 2,4 , 5 et 6 Ghz. Des décrochages , des demandes de connexion avec MDP , et…
-
NWE130BE access point
My NWE130BE access point is not accessibly anymore. LED shows steady green. Deregistered in Nebula Does not request a DHCP address Reset button does not work, Pressing for 10sec does not make the LED blink or reboot, LED stays steady green. Ethernet connection does not come up. Any idea how to proceed?
-
HAve this AP NWA50AX
Hey I have problem to logon to this AP i my house! i have config the AP and i can see the AP SSID and Pasw to the WIFI, but i can not connect to the AP non of my Devices! Then i take it withme to my job connect to my Working plave network and all works! all my Laptop and my Iphone works without make some config to the AP,…
-
NWA50AX-Pro Access Point Issues
I've encountered several issues while configuring the Zyxel NWA50AX-Pro access point via Local Web Interface (browser - Chrome). I don't know if this relates to the browser and/or Nebula (which I don't use) as well. 1 - In an earlier post I noted the NWA50AX-Pro won't connect via https without browser warnings. I've been a…
-
NWA50AX PRO WLAN - IP Adress from Router not NAT
Hello, I am currently dissatisfied with the Wi-Fi connectivity of my access point (NWA50AX PRO) and hope that there is an optimized solution for this. Network structure: My home network is set up as follows: Internet → Router → LAN → Switch → LAN → Access Point → Wi-Fi IP addresses in the network are assigned via DHCP from…
-
Broadcasting Hidden Network SSIDs
WBE660S is broadcasting hidden network SSIDs on 5G and 6G band (2.4G is working as intended) after updating devices to firmware v7.20 Patch 1. Any solutions other than rollback firmware. Thanks.
