ATP100: SFP/Modem little bit slow?
Options
Hi folks!
I have a ATP100 here and when I also use it as a modem with plugged-in WAN fiber cable directly into the ATP100, I receive between 400-500Mb/s in download-transfers (multiple streams, different servers tried etc.).
When I use the original modem of the provider (Swisscom, Internet-Box 3), I receive 960Mb/s per second. Of cause I don't expect these rates behind the firewall, but when I make a forwarding from the provider modem to the ATP100, I receive 650-700Mb/s which is pretty nice.
I want these rates directly from the ATP100 with plugged-in WAN fiber, but it seems to much for the ATP100?!
Do I have to swap to the ATP200 to get these rates?
I know that the ATP500 could handle this for sure, these firewalls are beasts, but I don't won't to spend this much in my Home-Setup.
Sorry for my strange spelling.
Greeting from Switzerland
Best Regards
Jonas
I have a ATP100 here and when I also use it as a modem with plugged-in WAN fiber cable directly into the ATP100, I receive between 400-500Mb/s in download-transfers (multiple streams, different servers tried etc.).
When I use the original modem of the provider (Swisscom, Internet-Box 3), I receive 960Mb/s per second. Of cause I don't expect these rates behind the firewall, but when I make a forwarding from the provider modem to the ATP100, I receive 650-700Mb/s which is pretty nice.
I want these rates directly from the ATP100 with plugged-in WAN fiber, but it seems to much for the ATP100?!
Do I have to swap to the ATP200 to get these rates?
I know that the ATP500 could handle this for sure, these firewalls are beasts, but I don't won't to spend this much in my Home-Setup.
Sorry for my strange spelling.
Greeting from Switzerland
Best Regards
Jonas
0
Accepted Solution
-
Yeah… I should say, that this was of course, all ATP features were activated. All my fault. Sorry for the late response
0
All Replies
-
Did the ATP100 connect with modem by Ethernet to get performance 650-700Mb/s ?
0 -
Jeremylin said:Did the ATP100 connect with modem by Ethernet to get performance 650-700Mb/s ?
Fiber-cable with SFP/miniGBIC from the wall-socket into the modem. From the modem with Ethernet (copper) into the WAN of the ATP100. Speed: 650-700Mb/s
Fiber-cable with SFP/miniGBIC from the wall-socket into the SFP-slot of the ATP100. Speed: 400-500Mb/s
Firmware is V4.60(ABPS.0).
EDIT: Perhaps I should add, that I receive 960Mb/s without the ATP100 at all (so just with the modem). So the fiber-WAN is not the problem.0 -
Yeah… I should say, that this was of course, all ATP features were activated. All my fault. Sorry for the late response
0
Categories
- All Categories
- 396 Beta Program
- 2.1K Nebula
- 117 Nebula Ideas
- 81 Nebula Status and Incidents
- 5.1K Security
- 86 USG FLEX H Series
- 247 Security Ideas
- 1.3K Switch
- 69 Switch Ideas
- 915 WirelessLAN
- 34 WLAN Ideas
- 5.9K Consumer Product
- 211 Service & License
- 337 News and Release
- 71 Security Advisories
- 21 Education Center
- 5 [Campaign] Zyxel Network Detective
- 2K FAQ
- 912 Nebula FAQ
- 419 Security FAQ
- 237 Switch FAQ
- 207 WirelessLAN FAQ
- 46 Consumer Product FAQ
- 139 Service & License FAQ
- 34 Documents
- 34 Nebula Monthly Express
- 72 About Community
- 62 Security Highlight