USG310 - L2TP VPN - GUI Error? - Unable to select VPN Connection
AaronReynoldsUK
Posts: 4
in Security
I have a fully working IPSec and L2TP VPN on the firewall. Tested and used for 2yrs+.
Just upgraded to v4.72 (latest) firmware. Model is USG310.
GUI Page = VPN > L2TP VPN
Issue:
The drop-down for "VPN Connection" now contains "Please select on..." and the only option is "none".
Expected Behaviour:
The configured IPSec VPN should be selectable (was previously).
Notes:
Not sure if the requirements have changed or if this is a fault in the GUI.
Just upgraded to v4.72 (latest) firmware. Model is USG310.
GUI Page = VPN > L2TP VPN
Issue:
The drop-down for "VPN Connection" now contains "Please select on..." and the only option is "none".
Expected Behaviour:
The configured IPSec VPN should be selectable (was previously).
Notes:
Not sure if the requirements have changed or if this is a fault in the GUI.
0
Best Answers
-
Hi @AaronReynoldsUK,
Welcome to Zyxel community.
This is not expected behavior. Can you send me startup configuration file in PM for further checking?
Thanks.0 -
Zyxel_Cooldia said:Hi @AaronReynoldsUK,
Welcome to Zyxel community.
This is not expected behavior. Can you send me startup configuration file in PM for further checking?
Thanks.
Zyxel_Cooldia identified that I was incorrectly using "mode config" on the IPSec configuration (incompatible with/overriding L2TP on ZyXEL), once disabled the VPN Connection was again selectable in L2TP configuration.
1
All Replies
-
Re check vpn connection and VPN gateway settings for L2TP VPN
1 -
Later versions (4.x) sometimes to not have any L2TP gateway/connection configured.You can re-enable them with a specific terminal command documented into a KB.1
-
Hi @AaronReynoldsUK,
Welcome to Zyxel community.
This is not expected behavior. Can you send me startup configuration file in PM for further checking?
Thanks.0 -
mMontana said:Later versions (4.x) sometimes to not have any L2TP gateway/connection configured.You can re-enable them with a specific terminal command documented into a KB.0
-
Zyxel_Cooldia said:Hi @AaronReynoldsUK,
Welcome to Zyxel community.
This is not expected behavior. Can you send me startup configuration file in PM for further checking?
Thanks.
Thank you.
I've PM'd you a redacted startup config.0 -
Zyxel_Cooldia said:Hi @AaronReynoldsUK,
Welcome to Zyxel community.
This is not expected behavior. Can you send me startup configuration file in PM for further checking?
Thanks.
Zyxel_Cooldia identified that I was incorrectly using "mode config" on the IPSec configuration (incompatible with/overriding L2TP on ZyXEL), once disabled the VPN Connection was again selectable in L2TP configuration.
1 -
Is there any solution for this error or should we just throw Zywalls away?0
-
zyxel support ridiculous0
-
Hi @hgmrtn,
Welcome to Zyxel community.
Please help to check if mode config is tick in VPN phase 2.Go to IPSec VPN > VPN Connection > RemoteAccess_L2TP_Wiz > Mode Config.Turn off "Enable Mode Config". Mode Config is for software IPSec VPN client (the green bow client).
Then you can find it appears on the drop-down list of L2TP > VPN Connection. On this page, IP Address Pool assigns IP addresses to L2TP VPN clients, so you don't need to configure Mode Config in VPN Connection > RemoteAccess_L2TP_Wiz.0
Categories
- All Categories
- 347 Beta Program
- 2.1K Nebula
- 115 Nebula Ideas
- 77 Nebula Status and Incidents
- 5K Security
- 44 USG FLEX H Series
- 246 Security Ideas
- 1.2K Switch
- 64 Switch Ideas
- 900 WirelessLAN
- 33 WLAN Ideas
- 5.8K Consumer Product
- 204 Service & License
- 326 News and Release
- 71 Security Advisories
- 21 Education Center
- 5 [Campaign] Zyxel Network Detective
- 1.8K FAQ
- 832 Nebula FAQ
- 402 Security FAQ
- 219 Switch FAQ
- 190 WirelessLAN FAQ
- 45 Consumer Product FAQ
- 136 Service & License FAQ
- 34 Documents
- 34 Nebula Monthly Express
- 71 About Community
- 61 Security Highlight