Turn off Status LEDs

Tissi_2
Tissi_2 Posts: 3
First Comment
in Switch

Dear ladies and gentlemen,

I am planning to buy a managed switch. Is it possible to switch off the LEDs on the GS1200 models? For me this is a required feature since I don't want to be distracted by blinking lights.

Best regards
Tissi

Accepted Solution

  • PeterUK
    PeterUK Posts: 3,389  Guru Member
    100 Answers 2500 Comments Friend Collector Seventh Anniversary
    Answer ✓

    I don't think you can…

«1

All Replies

  • PeterUK
    PeterUK Posts: 3,389  Guru Member
    100 Answers 2500 Comments Friend Collector Seventh Anniversary
    Answer ✓

    I don't think you can…

  • Tissi_2
    Tissi_2 Posts: 3
    First Comment

    Dear Zyxel,

    please implement an option to switch off the status LED lights on the LAN ports. Netgear and other competitors implemented this option upon several consumer requests.

    Best regards

    Tissi

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,103  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security

    Hi @Tissi_2

     

    The GS1200 Series switch does not support the option to turn off the LED lights. However, we appreciate your suggestion and will definitely raise this feature as an idea for our future products. We will evaluate and consider the feasibility of implementing this feature in our upcoming plans. Thank you for your valuable feedback! 😁

     

    I have raised this feature request at the idea section: 
    GS1200 Series switch status LED can be disable — Zyxel Community 

     

    Kay 

    Kay

    Untitled Image

    Share your feedback through our survey, make your voice heard, and win a WiFi 7 AP! https://bit.ly/2024_Survey_Community

  • Tissi_2
    Tissi_2 Posts: 3
    First Comment

    Dear Kay,

    thank you very much for forwarding this idea to your development department! I have more ideas for your switches, but this would not match the thread topic.


    You have written that this idea might get implemented in future products. Wouldn't it be smart to implement this feature via a firmware update in all existing capable products?

    Best regards

    Tissi

  • PeterUK
    PeterUK Posts: 3,389  Guru Member
    100 Answers 2500 Comments Friend Collector Seventh Anniversary

    Thier is firmware then thier is hardware the question is can firmware tell hardware to turn off the LED? or are the LED hardware only that firmware can't control?

    You could use a strip a black tape😏

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,103  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security

    Hi @Tissi_2

     

    We are happy to inform you that we have confirmed that the status LED can be disabled via a firmware upgrade, and this feature has been added to our future roadmap. 

    If there is a new firmware release that includes this feature, we will keep you informed through this forum. We appreciate your feedback and suggestions, and we always welcome new ideas from our users. 😀 

     

    Kay   

    Kay

    Untitled Image

    Share your feedback through our survey, make your voice heard, and win a WiFi 7 AP! https://bit.ly/2024_Survey_Community

  • TheGiolly
    TheGiolly Posts: 3
    First Comment

    Are there any updates on this?

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,103  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security

    Hi @TheGiolly

     

    This feature has been raised as an idea on our Swtich Ideas section, you may check it out here: 
    GS1200 Series switch status LED can be disable — Zyxel Community 

    If you're interested, please leave your vote and any comments on the idea. We'll be monitoring the feedback as part of our evaluation process. 

     

    Kay 

    Kay

    Untitled Image

    Share your feedback through our survey, make your voice heard, and win a WiFi 7 AP! https://bit.ly/2024_Survey_Community

  • PavSve
    PavSve Posts: 4  Freshman Member
    First Comment Friend Collector

    Hi!
    I'm looking forward to updating the firmware so I can turn off the LEDs on my Zyxel GS1200-5 and GS1200-8 switches. It disturbs me while working and sleeping.

    I would like to see the LED turned off on the GS1900 series as well.
    Ideally the ability to set the LEDs on each port separately.

    Thanks!

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,103  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security
    edited September 2023

    Hi @PavSve

    Yes, we have included the feature of LED turn on/off feature on GS1200 Series switch to our roadmap and the schedule is currently being evaluated. Please stay tuned on https://community.zyxel.com/en/categories/switch-news-and-release for the latest updates.

    Your request for the port status LED turn on/off button for the GS1900 Series switch is also greatly appreciated. We've created an idea post for this feature in our community. You can find it here:

    https://community.zyxel.com/en/discussion/18715/gs1900-series-switch-port-status-led-turn-on-off-feature

    If anyone likes this idea, please feel free to leave a comment or click vote. The votes and comments will be part of our evaluation process.

    By the way, could you please share why you would like to set the LEDs for each port separately?

    Kay

    Untitled Image

    Share your feedback through our survey, make your voice heard, and win a WiFi 7 AP! https://bit.ly/2024_Survey_Community

Categories

Switch Help Center

EnglishTiếng ViệtРусскийไทย中文（台灣）