Channel utilization missing from the SNMP MIB?

rwhitton
rwhitton Posts: 4
First Comment
edited May 21 in Wireless

Is there a good reason that the channel utilisation (for each channel) figure doesn't appear to be available in the SNMP MIB? I've had a good search for it and drawn a blank. If I've missed it then can someone advise the OID?

Specifically I'm using WAX510D access points but I expect it applies to all of the models that report the channel utilisation in the web interface.

Are there any plans to add this to the MIB? It would be useful. I have an interference situation. Occasionally the channel utilisation spikes in the 90% region. To help determine the root cause I want to be able to read this value every few seconds and chart the results against time to look for a pattern.

Accepted Solution

All Replies

  • Zyxel_Judy
    Zyxel_Judy Posts: 1,631  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security Zyxel Certified Network Engineer Level 1 - Nebula

    Hi @rwhitton ,

    Currently, there is no OID available for monitoring channel utilization in APs.

    that report the channel utilisation in the web interface

    The feature to monitor channel utilization is available in both Standalone and Nebula Cloud modes, with different navigation paths for each mode.

    In Standalone mode:

    Monitor > Wireless > AP information > Radio List

    image.png

    In Nebula mode:

    Device > Access points

    image.png

    Occasionally the channel utilisation spikes in the 90% region

    High channel utilization often indicates significant interference within your network environment. To potentially resolve this issue, you may adjust specific settings related to the radio channel width and DCS same to the image below.

    image.png

    By the way, keep your APs away from other electronic devices that can cause interference, such as microwaves, cordless phones, and Bluetooth devices. Also, physical obstructions like walls and furniture can impact signal strength and increase channel utilization.

    Judy

    Untitled Image

    See how you've made an impact in Zyxel Community this year! https://bit.ly/Your2024Moments_Community

  • rwhitton
    rwhitton Posts: 4
    First Comment

    Zyxel should add this to the MIB, however in the meantime…

    I bodged what I wanted (i.e. a means to periodically poll the value) via ssh in bash:

    while true
    do
    echo "show wireless-hal statistic" | sshpass -p my_password ssh -T admin@access-point.my.domain | grep Channel | paste -s | ts >>/tmp/wifi.log
    done

    (note ssh must be enabled in the AP)

    Without worrying too much about the timebase this can then simply be turned into a plot with something like:

    cat /tmp/wifi.log | cut -d' ' -f8 | gnuplot -p -e 'plot "/dev/stdin" with points'

  • Zyxel_Judy
    Zyxel_Judy Posts: 1,631  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security Zyxel Certified Network Engineer Level 1 - Nebula
    Answer ✓

    Hi @rwhitton ,

    Thank you for your sharing.

    Related to the Channel Utilization OID, we are considering this as a potential feature for future evaluation. You can view and contribute to this idea in the following section:

    https://community.zyxel.com/en/discussion/22165/addition-of-channel-utilization-oid-for-snmp-use

    Thank you for using Zyxel products and service.

    Judy

    Untitled Image

    See how you've made an impact in Zyxel Community this year! https://bit.ly/Your2024Moments_Community

Categories

Wireless Help Center

EnglishTiếng ViệtРусскийไทย中文（台灣）