Trunk configuration

Gel
Gel Posts: 23  Freshman Member
First Comment Friend Collector Second Anniversary
edited October 17 in Security

I have two WANs with 200MB Full each. How do I make it so that when WAN1 goes down, WAN2 goes up automatically?
Do I need to configure something in routing besides creating the trunk?
How do I create Trunk so it works this way?

I'm using the USG FLEX 200


Thanks

All Replies

  • zyman2008
    zyman2008 Posts: 223  Master Member
    25 Answers First Comment Friend Collector Seventh Anniversary

    Hi @Gel ,

    Just setup a Trunk and set it as default.

    1. Create a new Trunk. Set the primary link ac active mode and backup link as passive mode.
    image.png

    2. Select this Trunk as default

    image.png

  • Gel
    Gel Posts: 23  Freshman Member
    First Comment Friend Collector Second Anniversary
    edited October 18

    @zyman2008

    Thanks for the information. One more thing: In my corporate network I created a routing so that the internal LAN1 leaves via WAN1. With this change in the trunk that you told me about, what would this runting look like? Do I have to delete it? Or should I do some other configuration so that it works the way I said, if WAN1 goes down, WAN2 goes up and we don't run out of internet?

    Thank you very much for the help.

    trunk.png

  • valerio_vanni
    valerio_vanni Posts: 116  Ally Member
    5 Answers First Comment Friend Collector Third Anniversary

    Yes, this way LAN1 can go out only on WAN1.

    You should create another policy route for LAN1.

    #1 pointing to WAN1

    #2 pointing to WAN2

    Both with "healthy check". So, if WAN1 is working, #1 is used. When WAN1 is down, #1 gets disabled and #2 is used.

  • zyman2008
    zyman2008 Posts: 223  Master Member
    25 Answers First Comment Friend Collector Seventh Anniversary
    edited October 19

    https://community.zyxel.com/en/discussion/comment/70739#Comment_70739

    Hi @Gel,

    Change the next-hop of this policy route to the new Trunk.

    Note: you need to enable and setup connectivity check in the primary interface.

    What valerio_vanni mentioned is also a solution.

    My preference is to use trunk to set up. It makes the policy route table cleaner. Too many rules often make it difficult for me to debug.

  • Gel
    Gel Posts: 23  Freshman Member
    First Comment Friend Collector Second Anniversary
    image.png 
    would it be like that? Instead of interface, put configured trunk
    Would this be a second option?
                            
    
                        
        
                        
    
                
    
            
    
        
    • 
                
  • 
            
    

                                                                
    
                    valerio_vanni                    
                        
    
                        
                                valerio_vanni
                        

                        
                            Posts: 116   Ally Member
    
         
            5 Answers
         
         
            First Comment
         
         
            Friend Collector
         
         
            Third Anniversary
         
                                
                    
    
                    
    
                        
                                                   
                                                                    
    
                    
                                                
    
                                                    
    
                                    
    
                
    
                    
    
                        
    
                            
    
    
        https://community.zyxel.com/en/discussion/comment/70827#Comment_70827
    

    

    Yes, trunk method is simpler than mine.
    You can SNAT to outgoing interfaces, I use the other method because I have to SNAT to different addresses.
                            
    
                        
        
                        
    
                
    
            
    
        
    • 
                
  • 
            
    

                                                                
    
                    Gel                    
                        
    
                        
                                Gel
                        

                        
                            Posts: 23   Freshman Member
    
         
            First Comment
         
         
            Friend Collector
         
         
            Second Anniversary
         
                                
                    
    
                    
    
                        
                                                   
                                                                    
    
                    
                                                
    
                                                    
    
                                    
    
                
    
                    
    
                        
    
                            
    Thank you everyone for the information. Next Saturday I will make the changes and see how the network behaves. Once again thank you all very much.
                            
    
                        
        
                        
    
                
    
            
    
        
    • 
                
  • 
            
    

                                                                
    
                    Gel                    
                        
    
                        
                                Gel
                        

                        
                            Posts: 23   Freshman Member
    
         
            First Comment
         
         
            Friend Collector
         
         
            Second Anniversary
         
                                
                    
    
                    
    
                        
                                                   
                                                                    
    
                    
                                                
    
                                                    
    
                                    
    
                
    
                    
    
                        
    
                            
    
    
        https://community.zyxel.com/en/discussion/comment/70829#Comment_70829
    

    

    I tried to configure it with trunk and it didn't work. I'm putting some images to see if I made the right configuration.
    where I circled in red, is the configuration correct? Does it have to be like that?
    
    
    
        
            trunk1.png
    
    

    

    In the routing option, in the route policy, when editing my LAN1 in nexte-rop, do I put trunk? Could it be that when WAN1 goes down, WAN2 goes up automatically?
    
    
    
        
            trunk2.png
    
    

    

    Would this be the configuration? Thanks in advance for your attention. Thank you very much.
                            
    
                        
        
                        
    
                
    
            
    
        
    • 
                
  • 
            
    

                                                                
    
                    Gel                    
                        
    
                        
                                Gel
                        

                        
                            Posts: 23   Freshman Member
    
         
            First Comment
         
         
            Friend Collector
         
         
            Second Anniversary
         
                                
                    
    
                    
    
                        
                                                   
                                                                    
    
                    
                                                
    
                                                    
    
                                    
    
                
    
                    
    
                        
    
                            
    
    
        https://community.zyxel.com/en/discussion/comment/72145#Comment_72145
    

    

    Did I make the correct configuration?

                            
    
                        
        
                        
    
                
    
            
    
        
    • 
                    

            
    

                                                                    

                                

                                
                                

                                    

                                        

                                    

                                    


    
    
    


        
Categories

        
    

 
 





    

        
Security Highlight

            

                

                

                Read more
            

    







    
Security Help Center

            
    



    
 
                                

                                

                            

                            
                        

                    

                

            

        

    

    
EnglishTiếng ViệtРусскийไทย中文（台灣）