-
alternate failed log in
If, alternately, I put http://setup.zyxelinto the brower I do get the login screen for the Zytel switch, BUT even though I have held the reset button for minutes, it will NOT accept the default values and I can not log in - so can NOT do ANYTHING with switch. Help, please!
-
Link Aggregation - 10G & 1G
Hi, I have a PC with a 10Gbe NIC and a NAS with a 10Gbe NIC and two 1Gbe NICs. If I connect both 10Gbe NICs to the Zyxel switch as well as my TV, someone can watch something on the TV streaming from the NAS. If I then copy a large file (a 4K film for example) from my PC to the NAS, it often causes the connection from the…
-
GS1910-24HP how to configure VLAN`s ?
Hi, I'm trying to setup VLAN`s on old GS1910-24. Device info: Software Software Version V1.00(AAAY.3) Software Date 2013-03-05T10:42:04+01:00 Code Revision 40c11c4fd061 Unfortunately in VLAN Port Configuration I cannot add all VLAN`s like I saw in other Zyxel switches At the moment AP`s keep getting IP`s from the range…
-
Fan speed control on Zyxel switch?
I have a 48 port variant of the Zyxel managed switch. It's in my garage which is very cool in temperature, especially this time of year (very wintery October/November) around 50°F. Currently, I have found no way to control the fan speed which seems to be full throttle all the time. I get the reason is to prevent…
-
Power usage increase on XGS1250-12 V2 firmware
Hi, I upgraded the firmware of my XGS1250-12 from V1.00(ABWE.3)C0 to 2.00(ABWE.0)C0 and now the power usage has increased. The green graph is the time left on my UPS and it has decreased significantly. Anyone else seen this?
-
Download latest firmware for GS1200-8 and GS1200-8HPv2
I cant download those files. Seems i dont have access. Could you please make them public available? https://community.zyxel.com/en/discussion/9591/fixed-gs1200-8-8hpv2-management-ip-address-issue/ thanks Simon
-
Small HomeLab network system
Hello! I have an idea to use these devices for my HomeLab and manage it through NebulaFLex. I already have MikroTik Chateau LTE router. Switch GS1915-24EP - 1.pcs + Access point NWA50AX - 3.pcs + other RJ45 connections - 8pcs. and some time later 6 security cameras might be added but for that my idea is to use separate PoE…
-
GS1900-8HP A.1 down after upgrade to 2.70(AAHI.5)C0
I have an old GS1900-8HP revision A.1 that was on firmware 2.60. After upgrade to 2.70(AAHI.5)C0 on the boot partition I lost access. I connected directly and got an address on VLAN.1 (should have been 10), which suggests it lost its configuration. I tried factory resetting and connecting to http://192.168.1.1, again…
-
GS1920-24hpv2 problem with VoIP/Vlan
Hello everyone, sorry for my English. I installed a gs1920-24hpv2 switch like this: Port 24 Data Trunk (VLAN 1) Port 23 Voice Trunk (VLAN 20) VLAN 1 Data, all ports, except 24, have been set untagged VLAN 20 Voice, all ports tagged except 24 and 23 I excluded port 23 from VLAN 1 and set it to untagged 20 Port 23 is…
-
GS1350-26HP Installation
Good morning, I purchased a GS1350-26HP to connect my POE cameras. I connected the switch to the NR7101 5G antenna but unfortunately I can't connect it to Nebula or connect to the web GUI. I also connected the switch directly to the PC, trying to connect to 192.168.1.1 but I can't find the page. I also changed the address…
-
problem
I have ZYXEL GS2210-24HP switch. After firmware update to and update rom and reboot: Messages: Bootbase Version: V1.00 | 12/18/2013 13:20:50 DRAM calibration...PASSED RAM: Size = 131072 Kbytes DRAM POST: Testing: 131072K OK DRAM Test SUCCESS ! ZyNOS Version: V4.50(AANE.4) | 07/08/2020 13:42:42 Press any key to enter debug…
-
GS1200-5 trunk port
Looking into this product and i was wondering how do i create a trunk port to the router and vlans assigned to each port? in more detail i would like to have eth1 to be trunk port and carry all vlans to my router, eth2-5 assigned to vlan20,30,40,50 respectively.
-
ugly bug in IPV6 config part of latest XMG1915-10E switch firmware?
2 new XMG1915-10E, both with latest V4.80(ACGO.1) firmware, configured standalone: (IP, DNS et al via DHCP and DHCPV6 active on VLAN 1, just one VLAN with ID 1) on both, almost always when I try to ask for details of the IPV6 status of vlan 1 (System - IPV6 - IPV6 Status - click on the only VLAN with index 1) the switch…
-
how do you manually update firmware on NSW100-10 switch?
-
Is it possible to use the static mac features to map to different vlans with gs1900?
Lets say I want to use a small unmanaged hub or switch plugged into a single port on the gs1900. Is it possible to use the static mac features to map static mac addresses to different vlans for each mac address? If so, what should the PVID on that port be set to? And the VLAN Port configuration - what should that look like?
-
ZYXEL GS-105B v3 priority:
Hello. Question about ZYXEL GS-105B v3. What is the difference between MED and HIGH ports? Is MED slower? Which port has higher priority: HIGH or MED? Thank you.
-
modem and Zytel switch seem to have same address
when it comes to networking, I understand almost nothing. When I input my switch IP address into browser I get login screen for modem. Kindly help, as I can do NOTHING with the Xytel switch now. Thanks
-
I tried to register my switch and I got an error "Cannot find device"
Can someone from Zyxel help me please
-
XMG1915-10E and self-signed certificate
Hi, Am I able to import self-signed certificate via GUI on XMG1915-10 for browser HTTPS access?
-
Stacking ZYXEL XGS 2220 54HP
Hello, I recently acquier 3 Zyxel XGS 2220 54HP, i have stack my swtich with DAC10 cable. Once i activate stacking mode, i can't configurate port 51-54 with VLAN. I want to use the last 2 ports (53 and 54) for stacking and the other for SFP fiber VLAN for other switch connection. It that possible ? I saw on the notice it…