-
Help required with a VLAN ZYXEL noob question
Hope some one can help me with configuring VLANs on the below kit, I have the following setup… ZYXEL - VMG8825-T50 ZYXEL - GS1200-8 The router is in the basement and the 8 port switch is in the loft, the gigabit uplink to the loft switch is from LAN1 on the router to port 1 on the eight port switch. Here is my question: I…
-
Configure GS1900-24HP to block internet access for IP Cameras?
I have multiple IP cameras. Is it possible to create a configuration (Virtual Network?) that will block the cameras from accessing the internet? Could I do the same thing by configuring the cameras with a bogus Gateway address? Would this protect cameras from internet probing? Thanks!
-
XGS1250-12 LACP support ?
Hello ! Is it possible to support LACP port aggregation for the XGS1250-12 model? I purchased this model hoping for port aggregation with Synology !!! Are looking forward to !!!
Thank you
-
Zyxel XS3800
Good afternoon. I have 2 XS3800 in stock installed. aggregation is done on 4 ports. T9 port 1/9,2/9, T10 1/10,2/10. They have connected servers on which bond round robin is assembled. When testing iperf from one server to another (from T9 to T10). Traffic from T9 (1/9 -5Gb/s, 2/9-5Gb/s) for some reason goes to…
-
GS1900-24HP Firmware V1.00(AAHM.1) to latest?
Hi, Just purchased an old, now EOL GS1900-24HP. I've reset it and managed to get into the device. It currently is running firmware V1.00(AAHM.1) and I see that latest firmware is 2.70 (AAHM.3).C0. Can I upgrade directly from my current version to the latest or do I have to install other versions first (if so which and what…
-
Any ONU not working in Zyxel OLT-1308S-22
Hello Guys Dose anyone know if there could be another ONU Working in my Zyxel OLT-1308S-22
-
details for GS1900-24EP and GS190024HPV2
Hello, I have a question : The ports are 100/1000 Mbps compatible, are they compatible with 10 Mbps? Thanking you in advance for this clarifications.
-
GS 1900 Firmware Upgrade - 2.70v5 vs 2.70v3 differences
Hope this is not a repeat question. I was hoping someone could point me in the direction. I am upgrading a work switch. The obvious answer to upgrading would be to upgrade to 2.70v5 with no questions asked. I am curious if there is any way to get specifics about my current versions firmware(old 2.20) vs 2.70v5 vs 2.70v3. I…
-
Prevent Auto Logoff on GS1900-24E
I have Zyxel GS1900-24E running V2.70(AAHK.5). I am new to the switch so it takes time for me to administer the switch. While trying to make changes and following videos and/or instructions from internet I get logged off often. Is there away to prevent this from happening? I don't see a way to configure the inactivity…
-
SFP+ 10GBase-T Compatibility and XS1930-10 Questions
I am new to SFP+. I want to add an SFP+ 10GBase-T (RJ-45/Copper) to my XS1930-10 to use at 10Gbps. I tried a 10Gtek and while initially it seemed it was working fine I experience multiple problems. Can you pls share any 10GBase-T that works fine with the XS1930-10? Also, in the port status section, what am I supposed to…
-
What exactly does POE option "Disable PD" do?
I have a Zyxel GS1900-24EP. In the options to configure POE for a port, I can select to disable "PD state" (screenshot). The documentation says: "Select Enable to provide power to a PD connected to the port or Disable so the port cannot receive power from the Switch" (p. 132) On wikipedia, there is a table with stages of…
-
GS1900-24 Support
I have a few questions before I help decide should I buy a used GS1900-24 or not. I'm including a copy of the info I have on the item: 1/ Is this product still being supported or is it EOL? 2/ Can I update the firmware to v2.7 3/ Is there a version 2 of GS1900-24 Any help will be greatly appreciated
-
Linking Switches
Hi, I have a GS1920-48HPv2 used unmanaged, I need to link it to a CISCO SG300-28PP is this possible to do via SFP on ports 49 or 50? connecting to the link SFP port on the Cisco? all other ethernet ports are used on both switches. I need to share the internet connection between them so I'm thinking it will have to be done…
-
uplink GS-1920-24 v2 switchs
Hello everyone, I need advice to connect 2 GS1920-24 v2, with transreceiver modules and a fiber optic cable about 100m long. I just want to know if it is possible to do this with Zyxel SFP-SX-D modules. Thank you
-
Unmanaged Switch MG105 - ping ok, internet ko
Hi my switch mg-105 suddenly won't let me browse the internet. I can ping the router or other devices, but internet is down. If i connect the pc directly to router, internet works. Suggestion? Thanks
-
GS-1100 16 only giving 100M speeds
Hello all, Just wanted to get some understanding. I purchased this router and it advertised gigabit speeds allowed through the switch. The led lights (Green) indicate it is giving 1GbE speed but on any device plugged into it will only get 100Mbps. I've checked all the devices connected to it and they all have full duplex…
-
Need some help with IGMP Snooping settings on GS1900 switch
Hi, I just purchased a GS1900-16 switch and one of the requirements for the audio system we're using (Wheatnet) is that we enable IGMP snooping. They have some specific settings, but the information provided is for Cisco switches and I am not totally sure of the associated configuration settings for Zyxel. I'd really like…
-
GS2210-8 firmware please
Please provide firmware for the GS2210-8. The link here does not work for me:
-
GS1910-24 VLAN / Trunk-Port
I have a trunk cable (that comes from a router) which delivers the VLANs 40,60,70,80. Now I need to "split" that trunk to individual ports so that I can connect devices there. Devices are not capable to handle VLAN tags, therefore they must be removed on egress. On ingress the VLAN id must be added. I've tried that with…
-
Switch resetou após subir o firmware.
Após subir para a nova versão do firmware, o switch zyxel resetou para default, alguem sabe oque pode ter sido ?
