-
xgs2210 I lost ip interface
HelloI have 2 xgs2210 switches in a stack.I don't know why but I lost the web interface.I connected to the console to assign it a new management address but I have errors (routing table)do you have a procedure? Best regards
-
GS1920-24HPv2: Disabling SNMP?
Hello, in my Homenetwork I am using a GS1920-24HPv2 Switch. My question is: How can I disabling the SNMP because I have note found any disabling/deactivating option in menu "Management -> Access Control -> SNMP ->..." The newest Firmware is running on this switch. Thank you for your answer!
-
Problem with switch RGS200-12P
Hello everyone, I try configure vlan on my switch, i delete native vlan, create our vlan with tag 99. Create IP interfaces with adress 192.168.99.110 then i create trunk port. Why i can't connect to web interface switch from another site (192.168.1.0/24) when i create second ip interfaces witch adress 192.168.1.163 and…
-
PoE issue at GS1900-24HPv1 - Firmware 2.70(AAHM.1)C0
Recently upgrade to firmware 2.70(AAHM.1)C0 on all of our GS1900-24HP switches and all are dropping POE power for no reason and log does not contain any errors. Tried to do a tech support download but switch just rebooted and POE power came back. Any one else have issue with this firmware? For now I have rolled back…
-
Mismatch in port numbering with snmp on GS1920
Hi everybody, I'm monitoring my switches (GS1920-24HP and 48HP) in Observium or in Switchmap but there's a mismatch in the port numbering.The numbering begins by "0", thus if port #5 is in vlan 200, it's shown that it's port #4 who is is that vlan in observium.Has anyone experienced this problem ? Any suggestions to fix it…
-
GS1900-8 change ip problems
Hi to all, I have purchased and GS1900-8 managed switch, but I can't configure a new IP address. Configuring the PC connected via cable on the same factory subnet 192.168.1.0/24 does not detect the device via ping, TCP or via web browser. I tried on all physical ports (1 to 8), also factory reset but with identical results…
-
Zyxel switches distributor
DO you have distributor / reseller for your switches in Australia ?
-
ZYXEL GS1920-24HP, problem NTP
Hello, I am using a zyxel GS1920-24HP, the problem is that I can't set the time.
Whether by an NTP server (doesn't change the time) or manually. (When I restart the switch I lose time)
Thanks
-
xgs1250-12 LAG with Cisco switches
Hi! We're considering buying the xgs1250-12 switch to connect our router to the switch with a 10Gbit/s link. We have a few "old" Cisco switches and i saw that the xgs1250-12 supports link aggregation, but not LACP. How can I link aggregate the 2 or 4 1Gbit/s ports together and connect them to the 1Gbit/s Cisco switch?What…
-
XGS1930-52HP Switch port reset via cli
Hi, how can i reset a poe port (for restart like a cam) via cli? thanks tobi
-
ZyXel GS19xx VLAN Configuration Help
Hello, I'm trying to get some Virtual Lan Area Networks (VLAN) to work on my ZyXel GS1900-48 (V2.70) but I'm not having very much luck. My router / firewall is an OPNSense box with one VLAN (15) that is configured correctly (currently there is an allow any-to-any rule for testing purposes with a Dynamic Host Configuration…
-
GS1920-48v2 switches SFP ports 45-48 do not work
Good day, I am trying to connect two Zyxel GS1920-48v2 switches (GS1920-48v2-EU0101F)firmware 4.70(ABMK.7)C0using an SFP module (MikroTik XS+DA0001 - SFP/SFP+/SFP28 DAC cable, 1m)I reset the switch to factory settings scenario A:- when I connect both switches to the SFP port 50-50, everything works OK (only one cable)…
-
GS-1900 24HP
Where can I download the firmware for my zyxel GS-1900 24 HP switch, can you tell me the link please?
-
Help! Cannot figure out how to pass VLAN traffic between two GS1900-XX switches.
Hello, I've been trying to get a little lab setup using two Zyxel GS1900-XX switches. It works fine if using just the main (GS-1900-24) switch. But no go if using a port on the office (GS1900-16) switch. It seems that VLAN 5 (LAB VLAN) is not traversing the link between the two switches (port 24 on main switch & port 15 on…
-
GS1900-48 stops to exchanging data and I am forced to reset it
Hi, every 4/6 days mine GS1900-48 stops to exchanging data and I am forced to reset it. In my network there are 20 pc and many of these are used remotely or via Anydesk or via Microsoft Remote Desktop on a VPN connection managed by a Microsoft Server 2012. In GS1900-48 logs i can't find nothing except Port xx link up or…
-
How to get firmware and documentation for GS1900-10HP
On the north american site, putting the model GS1900-10HP comes up with no results in the Download Center. How do I obtain the latest firmware for this device.
-
GS1510-24 firmware
Where can I download the latest firmware? My switch is running what looks to be an archaic V1.00(BVN.1) Thank you, George
-
GS-108B v3 Problems with connections
Just installed this one and some problems occur. First im using Virgin HUB 5 + Linksys Mesh. So for start .. i plug all in and my mesh works all OK. Then i try to connect my PC via cable and no internet. Unplugged all. Restarted HUB, then Started Switch, Then Linksys mesh. My PC now has internet but no internet on Linsys…
-
ZyXEL XGS3700 Firmware Download
Hi Can't seem to find a download link for V4.20 firmware upgrade for a ZyXEL XGS3700-48HP. Downloads only has V4.30 as the lowest version that I can download but switch currently on V4.10 and will not upgrade to later version as they got to be done in order I presume. Any help would be appreciated.
-
Good News! 2.5Gbps <--> 1 Gbps Compatibility - XS1930-10
A few weeks ago I posted a question about the ability of the XS1930-10 switch to support 2.5 Gbps <--> 1 Gbps traffic (Multi-Gig to 1Gbs). I tested it and it works fantastic for my configuration. Prior to the XS1930, I tested Netgear and the little brother multi-gig Zyxel with no luck. Prior to the Xs1930 every time I was…