-
Vlan in GS1900-24
Hi Community I have a scenario where i want to connect 5 GS1900-24 switchs to a watchguard which each switch connected to an interface and each interface configured as vlan with dhcp server so my problem when i change the management vlan to other vlan id then 1 i cant get an ip address from watchguard neither get access to…
-
I can't log in after the GS1920-24HP firmware update
I updated the GS1920-24HP firmware to the latest and after restarting I can't log in to the interface because it doesn't accept the user who worked before the update. I tried to reset the device but did not see any change. What is the solution then?
-
Radius setup for AAA
We have a GS2210-24 setup with tekRADIUS for aaa accounting system radius and can authenticate fine however we are unable to setup our radius users as an administrator to make changes on the GS2210. I am guessing there is a vendor specific attribute I need to add for this to work.
-
GS1900 port VLAN ingress filtering vs trunk options
Hi,I have an GS1900-8 with which I have been very satisfied.However, I have read the manual and searched the forums and I'm uncertain on one thing. Does ingress filtering negate effects of enabling trunk?AIUI:* trunk enabled: permits the port to pass unknown VLAN tags. * ingress filtering enabled: disallows packets with a…
-
Difference between GS1920-24 and GS1920-24v2
What is the difference between those two, and would i be able to use the v2 firmware on the one i have? when i was looking for updated firmware there were no records of Zyxel GS1920-24 only GS1920-24v2. In settings this is what info i get. Device Type GS1920-24Boot Version V1.00 | 03/21/2014Firmware Version V4.50(AAOB.3) |…
-
Why Are There 2 Triangle Light Indicators For Every Port
Hi, For zyxel switches, why Are There 2 Triangle Light Indicators For Every Port? I understand that those pointing to the top refers to the interface on top. I understand that those pointing to the bottom refers to the interface on bottom. But why 2 triangles for each interface?
-
QoS trust DSCP on XGS1250-12
It's a pity XGS1250-12 does not support DSCP based QoS. At least it looks like it on the web configurator. But when logged in by serial UART (4 pin connector on the right side) there ist a "qos trust dscp" command and all the corresponding settings. Unfortunately I always get "Currently not in QoS basic mode" error. How to…
-
Reset des Swetch GS1920-24HPv2
Hallo Wie kann ich ein Reset machen. Es hat 2 versenkte Knöfe auf der Frontplatte mit der Bezeichnung Reset und Restore? Danke für die Hilfe Gruss Hans
-
Search MAC on XGS1210-12
Can Multigig Switch XGS1210-12 show MAC Address Table to search MAC locate on which interface ? Thank you
-
GS1900-48HPv2_2 Port LEDs always OFF after firmware update.
After updating to GS1900-48HPv2_2.60(ABTQ.4)C0 and entering the switch web interface, all the port LEDs on the status page image appear OFF, i.e. NOT green. If I activate the backup firmware version V2.60(ABTQ.0), they come back to life. I'm away from the switch, so I cannot say if even the fisical LEDs are OFF with the fw…
-
GS-105B v3 power supply
I lost the power supply to my switch GS-105B v3.On the device it says 5V 1A but what are the dimensions and polarity of the plug?Is it 2.1/5.5mm or 2.5/5.5mm or even another?Is it positive on center pin?
-
perche non trovo il software pwe lo switch MG-108?
ho comprato uno switcho mg-108, dopo aver ricevuto il link per scaricare il software e configurarlo, questo non funziona. Perche non permettere di scaricare il software direttamente dal sito dopo aver registrato il prodotto, piuttosto che rimandare ad un link non funzionante?
-
No Switch-Port Status in the Nebula Monitor
Hi Community, since a few weeks, in my Nebula Account the Status of the Switch-Ports are always "Disconnected". The other functions work correctly (MAC-Table or Ping). What can I do to solve this Problem? The Switches are up to date.
-
vlan configuration
I have a few vendor managed switches in my environment, netgear, dlink, tplink and they all play nice. I needed more ports in one of my closets, and the Zyxel GS1900-24 fit the bill. I am trying to set up the switch using ports 1, 2, 3 as trunk ports with tagged vlan ids of 100 + 200 and untagged management 1, which is how…
-
XGS1930-28 Ftp error 502
When i try to change dir with ftp i receive this error: 502 Command not yet implemented I want get and put configuration file, but i can't change dir (i want to go on conf directory). Thanks
-
How to get hold of GS1900-48 V2.70(AAHN.0)C0
Following the security advisory, I have been trying to find the referenced FW, but don't seem to be able to find it. On the Global (and UK) sites it is still 2.60 listed as the latest version. Simon.
-
Zyxel GS1920-24HP unsuccessful Mac-Authantication to radius !
Hi , I have Zyxel 1920-24hp switches and want to configure to MAC authanticate with radius. To do this I fallowed this post post https://community.zyxel.com/en/discussion/1565/is-there-a-way-to-configure-802-1x-mac-based-on-a-gs1920 Tekradius send success response but switch doesnt't allow client This is Tekradius Log…
-
Manage switch automatically via VPN
Hello, is it possible to connect two switches with VPN and the side witch automatically synchronizes the AP-Groups from the main switch?
-
GS1900-E24 perfectly running but unreacheable via https
Hi. I am searching some help for this problem. My switch is perfectly running as switch, but I am not able to reach it via web interface. Firstly I tryed at last saved address, secondly after keepeng pressed reset button for 15 seconds, (assuming 192.168.1.1 default address) I set my PC to 192.168.1.10 but nor me nor ZON…
-
how to set half duplex / full duplex on a GS1200
I found how to set the speed on a given port but don't see how to set half/full duplex. I need to set the port to 10M but full duplex (I believe the switch will default to half duplex when setting the speed to 10M).