-
setting up a VLAN, VLAN PC has Internet access but cannot ping each other within VLAN
Hello All, I am new to VLAN's and I know I'm close. Ultimately, I want to have 2 different networks that do not talk to each other, but do want them to talk within their own network and have internet access. Current setup regular network setup on a SonicWall Firewall with a 192.168.111.x on the first interface I setup a…
-
GS2210-48p randomly stops sending Radius requests
So I've noticed this a few times now. Randomly on some of the 60+ switches I have had them become inaccessible from login (both webpage and SSH). I can usually go into radius and disable the client then proceed to SSH into switch with the local creds. But the only way to get the switch back to talking through Radius is to…
-
GS1100-24E Unmanaged Switch Issue
Having issues with this switch. I have a verity of electronics connected to this switch and they are working fine. Tried a new CAT5E line in the house and now it won't give allow the router to provide an IP number for the computer. Tried 2 different lines and another computer and have the same problem. Connected the cable…
-
GS1900-10HP snmp default community string unexpected behavior and broken SSH enable password prompt
On the GS1900-10HP, both V2.40(AAZI.2) and V2.50(AAZI.0), there is a problem with the default screen that is presented recommending that the admin password and SNMP string be changed. On this screen, it is possible to change the admin password without changing the SNMP community string. However, if I attempt to change the…
-
Moved: GS1900-10HP snmp default community string unexpected behavior and broken SSH enable password…
This discussion has been moved.
-
How do I "split" GS1900-24 into 2 different IP Ranges?
Hi, Not sure if I am over thinking this but I have just received a GS1900-24 and wish to use ports 9-16 in a different IP range I have a Sophos XG Firewall DHCP server which has 2 networks 1 - 192.168.0.* I would like these to be ports 1-8, 17-24, 25 2 - 192.168.1.* I would like these to be ports 9-16 So do I need a VLAN…
-
GS19020-24HP ALM led red but device works
Hello On my switch, the red ALM led is lit on 2 ports but the peripherals (a Phillips TV and a Sonos connect) work perfectly. What can I check to correct this problem? I tried with another cable, the led stays on. Do you have another idea? Device type : GS1920-24HP Firmware : V4.50(AAOC.2) | 02/27/2018 Thank you
-
No firmware, console error message switch ES-2024
Hello, I tried to reset my switch ES-2024 to the factory defaults, but the process was not successful and the screen froze. After restarting I ended up with no firmware and when I try to get access trough the console it will show: CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCreceived = 0Received file size error!! ERROR After…
-
How can I use the SFP Ports on a GS1900-24?
Hi, I have a GS1900-24 and am utilizing the RJ45 ports as normal but I also have a 4 port Mikrotik 10gbe switch and pass one of those ports into the GS1900-24 switch but there is no LED showing connection and also shows no connection on the monitor. I have tried 4 different cables, copper & fibre but nothing shows as…
-
Access to the web interface of the xgs1930-052PH switch
Hello. Please tell me about the switch GS 1930-052PH. I can't log in to the web GUI when I connect to the switch via a local network (via another switch). There is a ping, the web interface tries to load, but even one screen loads for more than 5 minutes and resets. If there is no network connection and I connect to the…
-
How to properly limit bandwidth on GS1910-48 switch?
Hello Folks. I am trying to limit the bandwidth on my switch ports to 250Mbits. The problem is that when i apply the limitation on ports, the servers connected to it get packet loss. Even if they are consuming only 20Mbits. I am sure that i am doing something wrong... This is only the configuration i did (i didn't touched…
-
Configuring PoE Port as Trunk Enabled
We want to configuring VLANs throughout of wireless environment for network segmentation purposes. The challenge that we are currently facing is configuring our GS1100-8HP-240W PoE switch ports to trunk mode. This is required so all VLANs can be shared with APs as each VLAN has a dedicated SSID. Can we configure trunk…
-
Desktop ES116P desktop Ethernet switch
I have an ancient 10port box. Since getting a new BT router using superfast broadband any computer connected to any port cannot connect to the internet. I’m sure the connection between router and box is the same. My model number cannot be found in the Xyxel library.
-
GS1900-24E - V2.50(AAHK.0) - Bug in debug text for QoS Port Remark setting
I noticed that there is a wrong text in the debug log when changing the QoS Port Remark settings. For the "IP Precedence Remark" the text for "DSCP Remark" is inserted in the log. Istubled on this when enabling the remark dscp state and the log was showing it disabled it directly after enabling it. In fact it didn't, just…
-
Policy Rule Egress LAGG
We currently have a few Policy Rules setup for traffic egress on port 24 of our XS3700 as seen below. policy APolicy classifier AClass egress-port 24 priority 4 dscp 0 tos 0 bandwidth 500000 out-of-profile-dscp 0 priority-action prio-set metering out-of-profile-action drop policy Management classifier Management…
-
GS1900-24E
Ich habe mir den Switch zugelegt. Erreiche über meinen Computer leider nicht die angegebene Seite im Browser http:/192.168.1.1. um mich anzumelden. Ich habe als Router eine Fritzbox. Muss ich am Router oder am Computer etwas einstellen oder ändern? Vielen Dank vorab.
-
GS1900-48HP unable to access the GUI
I have reset the switch and attempted to access at 192.168.1.1. No response from ping. I don't see any devices in the arp list, even checked my DHCP server to see if it picked up an address... nothing. Unfortunately my model doesn't have a console port or I would be able to see what is really going on. I guess I have to…
-
XGS1930 - SNMP monitoring of a LACP link
Hello, I'm trying to monitor the bandwidth of a aggregated link but the SNMP data on my XGS1930 switch will only provide data for each individual port. Is there any way to get LACP link data out of SNMP?
-
Transfer config from GS1920 > GS1920v2
Hi, Is there a way to use/convert the config file backup from the older GS1920 to the newer GS1920 version 2 switch? Thanks. #Biz_Apr_2020
-
GS1200 VLAN issue
This discussion was created from comments split from: Weird password issues.
