-
VES1724-56 Randomly reset/reboot
Hi All, Can anyone know what is this error? Please see the photo below with yellow underline. After that error the device reboot/reset. Thanks,
-
Simultaneous Login
You can't login because the user already login from another IP. Please close the browser before next login. Goodbye! Hello,Does anyone know where you can turn off this check?This occurs on a GS-2210-48HP Switch ...Thank you.
-
Bought these : GS 1920-48HP & GS1920-24 - Link aggregation
I bought these 2 switches couple of days ago. Today I am setting up link aggregation between the 2 so the GS1920-24 has more bandwidth, is there anyone that could see if my setup is correct. I have them set them both with these settings in screenshot, is this correct or should I set something extra?
-
The strategy to level up your network skill!
Hi everyone, We have published an Handbook to help users learning fast on the Zyxel switch. Now, you may download it from the attachment link. Support Model: * GS1920 series * GS2210 series * GS3700 series * XGS2210 series * XGS3700 series * XGS4600 series There are some example and procedure for: * Basic settings…
-
Zyxel VES1724-56 System Logs
Good Day All, I have problem with my VES1724-56, but i can't see any system logs in the web GUI of the device. Where can i see the system logs so that i can study whats causes the issue. Note: My VES1724-56 keep on disconnecting for a split of seconds from the network and the modem clients is disconnected too in the device…
-
PoE with a loop via Zyxel GS 1200 to power EdgeRouter X?
My intention is to find out if it's possible to configure port 3 and 4 so, that for port 3 comes in a bridged LAN from bridge modem, and then it goes out from port 4 with PoE 24V, and that port 4 shall be connected to EdgeRouter X giving 24V power supply and internet. Reason for my intention is not to use PSE for ER X, nor…
-
Double NAT
G'day All, I have a ZyXEL vDSL DSLAM & a ZyXEL vDSL router. I have a NBN FTTN 100/40 connection with Commander. The cable run is 600 meters from the node & I get 55/30 to the frame. Commander have provided a Netgear modem & an audiocode router. The netgear is connected to the phone line & the audiocode which is then…
-
Cannot register on MyZyxel.com platform
Hi guys, I bought 2 GS2210-24 recently. When I tried to register them on MyZyxel.com, the website replied that the devices are not in the database. Does anyone know what can I do? Thanks! Best Regards, Dylan
-
Dynamic VLAN Configuration on XGS3700 Series
Does anyone know or have experience setting up DVLAN on an XGS3700? We have a radius server that will serve up the vlan to IP address mapping but what is the best way to accomplish the vlans on the switch?
-
Switch GS1900-8HP HELP HELP HELP !!!
I have a great problem with myself I can not help myself. I have 3 switches zyxel gs1900-8hp, purchased under ip monitoring. Unfortunately, switches only detect (8 ports in total) 4 IP cameras and port for DVR / laptop. When I plug the fifth ip camera, the switch does not detect it. But when I break any stone from the…
-
Bricked ZyXEL GS1900-24E after FW upgrade
Hi, I have just upgraded the FW on my ZyXEL GS1900-24E from v. 2.20 to 2.30. After the FW upgrade went through, the switch rebooted and since then the management web interface is not accessible anymore - neither using the custom IP from the configuration, nor the default 192.168.1.1. However, the basic switching…
-
Stacking & Link aggregation
Hi Everyone, I'm planning to purchase XGS2210 or XGS3700 for some office network usage.I would like to double confirm if these two devices can be configured physical stacking.If yes what should I pay attention with while setting up the environment?And can link aggregation setup using the port from slot1, slot2....slotX of…
-
GS1920-48HP for new office setup
Hello, For our new office I am looking to buy the GS1920-48HP . We have about 44 clients, 15 of them POE (VOIP, APS, some IP cams). Even though at 2 desks I would need to split again with another POE switch because there is only 6 cables and 8 clients. I don't know if can cause a problem to add a POE switch to a POE…
-
URGENT: Need VES-1624FT-55A management software
URGENT: Need VES-1624FT-55A management software. The download library shows the product in the drop-down but when you select it, it just says "no match found". We're experiencing an outage and it's very urgent. Thanks in advance!
-
Pinout Es-2024
Hello! I've ES2024, but I havn't console cable, because I want to know pinout conscole cable ES-2024 DB9-DB9 #Biz_Switch_October
-
GS2210-48HP Abnormal LED Behavior
Hi everyone, I have a GS2210-48HP in operation.I went to the server room to try and connect a new link on the switch. But I noticed that the LED of this port does not turn ON. After looking at the other ports, I noticed that some ports are also showing this behavior! The port that connects to the USG shows LED is OFF, yet…
-
XGS3600 SNMP
Hello everyone. We are monitoring our switches using SNMP. Have a lots of no response drops. Need to disable-enable SNMP on switches to get that statistic back. XGS3600-26F with Firmware Version V1.00(AABZ.2)C0
-
GS1900-8HP SNMP support
I'm trying to qualify this switch for use in one of our product offerings. The datasheet says that there is support for SNMP management and includes RFC1493 Bridge MIB in the supported list of MIBs. However, when I fetch the MIB information, I do not see this MIB included in the returned results. Is this MIB supported by…
-
LAG fails
I have 3 switches in the my company office. Old ProCurve 1800-24G and about one year old GS1900-24E and GS1900-8HP. Because of increasing traffic in the office I need more speed between switches.Therefore I tried to create 2 connections between switches to double the switch<->switch speed to 2Gbps. First I created LAG1 in…
-
Problem with ES-2024
Hello! I've have switch Zyxel ES-2024. But I din't know, it works or doesn't, but when I turn on it, indicators works. I try to connect to it by COM port, but i can't, because switch don't has reaction on trying to connection. What I need to do? Maybe is switch "brick" yet? Sorry for my English.