-
can I configure QOS in GS1900 for multicast streams?
Hi, I need to give higher priority to multicast strams in GS-1900, how should mange the switch? Appriciate any help #Biz_Switch_May
-
XGS2210-52 How to enable MTU size of 9k on VLAN (resolved)
How to enable MTU size of 9k on VLAN or in general. I am looking for the MTU size setting in the switch. Can anyone point me to the right menu?
-
VLAN setup between GS1920 Switch and Zywall USG20
I have a GS1920 switch I am trying to segregate into 4 seperate vlans and a DMZ. The vlans have been created on a USG20 Router using seperate subnets with their own DHCP servers. I wish to connect the router to the switch along a single LAN2 interface and have the switch separate out the traffic into port groups. At the…
-
What console cable is needed for a GS1910-24HP?
I have bought myself a used GS1910-24HP and cannot configure it - it is not on its default IP and nothing plugged into the console port returns anything, not even gibberish. The manual mentions no specific cable, and it doesnt look like there is a non standard pin out? #Biz_Switch_May
-
XGS4600 DHCP Global relay
We have an issue with DHCP relay on XGS4600. Step 1. Global relay is disabled, client not getting IP from DHCP server. Step 2. Global relay enabled, first address changed to our DHCP IP. Client getting proper IP. Step 3. Global relay first address changed back to default 0.0.0.0. Client getting IP (???) Step 4. Global…
-
XGS4600-32F Data abort occured
I lost inbound and outbound management access to switch during OSPF configuration process. Now SYS led blinking continuously. Getting log using RS-232 Data abort occured Fault Status = 0x00000008 Fault Addr = 0xE59FF570Current Task TCB = 0x6371AB28Current Task Name = PINICurrent Task Stack Start = 0x6371ABE0Current Task…
-
Trouble accessing login page for gs1900-8hp
I just received my Zyxel GS-1900 switch, and I seemed to have successfully changed its static IP address so it will not conflict with my router. The switch is not connected to my main router by an ethernet cable. It attached to another computer that is connected wirelessly to my router. To change the static address of the…
-
Assistance with Gs1900-16
Hello every one, I have bought GS1900-16 port to connect all my ethernet jacks to the switch and from the switch to the my current broad band router Motorola Surfboard sbv5220. No VLAN's or any of that as i was told my router not going to allow me to do this function + the VLAN option is more than what i need for my home.…
-
Can I segment a GS1900-24HP switch
My router has several LAN ports and I am using one as the DMZ port. The DMZ is on a separate IP subnet. I would like to eliminate a small switch that I am using to connect DMZ devices and manage the LAN and DMZ on a single switch. The router firewall manages traffic between LAN and DMZ. Can I segment the switch such that I…
-
Which firmware link?
I will be downloading the latest firmware for the GS1900-8HP switch. In the download library, there are two links under the "download column" for the latest firmware. Are they both identical? If they are different, it is unclear how. #Biz_Switch_May
-
GS-1100 16 PWR LED blinks fast
Hi Everybody, I have a GS 1100 16 and now my LAN ist gone. The PWR LED blinks very fast. I switched the power off and on again,but the LED still is flashing. Is the switch now at his end of life, or is it possible to reanimate it? Best Hoffi #Biz_Switch_April
-
GSX2210-28 Access To Web GUI Through Truck Ports and Different VLANS
I have Ports 25-28 Trunked and Aggregated to other switches on the network. When I try to access any of the interface IP's of the switch through the Trunk's even the Default the Web GUI is very slow and many times the session gets severed. The only way to access the Web GUI without any issues is by plugging directly into…
-
HTTPS: Create self-signed certificate with unique serial
Hi guys, I have got a bug report/feature request: When generating a self-signed certificate for HTTPS, the switch always uses its MAC address as serial number, which is not permissible and causes Browsers to reject connecting to the device when a certificate with the same serial is already known. For example in Firefox,…
-
GS2210-48 cisco-like vlan mode
Hi, I was trying to configure some GS2200 to interoperate with our installed switchs, there is a bunch of commands very similar to Cisco IOS, but when executed I get this message (config)# interface port-channel 1,2,3 (config-interface)# switchport mode trunk "VLAN configuration is current not in cisco-like vlan mode" Is…
-
Zyxel - simulation and visualization tool
Hi, I would like to ask, whether Zyxel have got a simulation and visualization tool (packet tracer in different Company)?
-
2 XGS2210-52 and USG 310
Hello, I need Yours help. I bought: - 2 switch Zyxel XGS2210-52 (switch are stacking) - 1 router model Zyxel USG 310 and I have problem with configuration. I need to create 3 vlans (10 for computers, 20 for CCTV, 30 for wifi guest). The Vlans should be isolated, but one computer form vlan 10 shoud manage CCTV and wifi…
-
SSH: Avoid "Write failed: Broken pipe" message when logging out gracefully.
Hi, another request for SSH: Currently SSH clients emit the error message like "Write failed: Broken pipe" or similar when logging out gracefully from a SSH/SFTP session to the switch. This is likely caused by prematurely closing a file handle without announcing a channel shutdown. The error message is confusing/leads to…
-
gs1900-8hp poe budget
Hi, I have 4 POE IP cameras (Power consumption 11.5W each - total 46W ) connected to my gs1900-8hp (which has a power budget of 70W). It also connects to 2 other gs1900-8hp switches and the NVR. So far so good. But when I connect another IP camera (power consumption 12.95W) it doesnt work unless I provide external power -…
-
Issue with P-871M (point-to-point connection)
Hello Team, I have an issue with establishing the connection between two 871m VDSL modems. My conditions: cable length is about 600 meters, the resistance on the line is 307 Om, two 871M modems. DSL indicators were blinking but connection was not able to establish. After I've reset settings to default on both devices the…
-
Faulty Cable?
Hi, I bought two GS1900-8 for home use. One is connected to the router (fritzbox) via port one. Router port is configured for 1Gbit speed. Once I set port 1 in the GS1900-8 to 1000M, full duplex manually I lose connection to the switch immediately. The other switch works fine (different setup though), so I’m not quite…
