-
WAX610D boot loop
Hi, my WAX610D runs a boot loop, using a console adapter i got the linked log. Is the device recoverable in any way with RMAing the device? I know my way around a bit in u-boot and embedded devices. https://drive.google.com/file/d/1Cx0kqktYF7MSRi0X7-QprrJdZCuZHnC3/view?usp=sharing Thanks.
-
NWA5123-AC
Hello EveryoneI have access point nwa5123-acIt was working correctlyToday it couldn't boot up...the led still orange without blinkingAlso it couldn't connect via ethernetI try to reset it...but it's not respondingWhat to do?
-
Firmware 4.72 WK28 as Wireless controller + iOS 15.6: any issues?
Good morning everybody, a customer which never experieced issues is signaling me that her iPhone updated to 15.6 had issues connecting to the wireless network. Wireless controller: USG60w 4.72 WK28 Wireless AP: NWA5123-AC firmware 6.10 AAZY.10 (both latest available) Two SSIDs, lying on the same vLAN (not the same as the…
-
NWA50AX Mesh Network
Hello, I just bought two NWA50AXs. Both connected to my switch via POE. My question refers to creating a proper home network. Both APs already share the same SSID/Passkey and everything seems to work just fine. Do I need to modify any settings for maximum efficiency and range? I want to avoid that one AP picks up the…
-
SNMP values
how can i set the snmp values on the access points? sysname syslocation both set to wac6552d-s . i would like to make it useful. thanks
-
NWA210ax ipv6 support?
The stats say it is supported but I don't see any options in the cloud for it.
-
AP firmware check failed
Hi, I updated my NXC5500 yesterday since yesterday midday till today morning I got wihtin minutes following alert
-
Speed For Wifi
I am using NWA110AX with 5GHz frequency. What is the a good speed for this AP? I am getting below 100Mbps. How do I know if this is good or bad?
-
WAX650S power mode and antenna
This discussion was created from comments split from: Wax650s.
-
RT3090 B/G/N COMPATIBILITY
Hi, I'm at my father's house and trying to connect his Windows 7 HP laptop to a Zyxel VMG3925-B10C router. The network card in the laptop is Ralink RT3090 802.11b/g/n and the driver is the latest one. The laptop connects to the WiFi but without Internet connection. If I log into the 192 page and turn off the security - the…
-
NWA210AX Power Consumption PoE
Hi, I have NWA210AX access point at home. Currently it runs over 802.3 PoE wich serve max 15.4 watt. I found that NWA210AX draws 19 watt. I enabled the "Force override the power mode to full power" setting on Nebula interface. I searched that if that raise a problem or not but seems it doesn't if there are not so many…
-
WAP6807 extender and DX3301 router
Can I use the WAP6807 extender with my DX3301 router? Are they compatible with the EasyMesh / Mpro Mesh system. I need to extend my WiFi signal and I have the DX3301 but I'm not sure that they can work together as mesh WiFi. I already know that the WAP6807 is not a WiFi 6 but is it not so important right now for me. Thanks!
-
NWA50AX L2 Isolation/Intra-BBS
So, I have 5 aps currently setup and am testing. I purchased these units know they did NOT have L2 Isolation but did not know about the Intra-BBS feature (not sure if its a feature available on the NWA50AX.) However, these options are available in the advanced SSID setup in the cloud. I have enabled these features for my…
-
VLAN ID not working
The access point is NWA55AXE. I would like to create a multi SSID access point..I tried to assign a VLAN ID to each SSID Profile but it does not work . Only if I leave VLAN ID =1 the profile allows clients to navigate. The switch has the tagged port where AP is connected with VLANID = 2 and 3. The respective SSID profiles…
-
Wifi Bağlantı Kopma Sorunu
Kullandığım cihaz ile ilgili olarak, telefon üzerinden bağlandığım da hep kopmalar yaşanmakta veri kaybı yaşanmakta bu çok can sıkıcı bi hal almaya başladı bununla ilgi sorunumun giderilmesini rica ediyor Türknet fiber kullanıyorum ama kablo harici bağlantıda sorun yaşıyorum ?????
-
NXC2500 firmware update
Hi Team, We want to upgrade firmware of NXC2500 from V4.22(AAIG.1) to the latest. Please help us to choose the latest firmware. Presently WAC6103D-I are connected to NXC2500. Regards, Pawan kumar
-
iwpriv(kickmac) - question regarding log
Hi community I have 3x NWA1123-ACv2 which are managed via Nebula. They broadcast the same SSID on both 2.4Ghz and 5Ghz. They work very well so far but recently I noticed that my iPad 8th Gen gets regularly kicked by the same AP (the closest one) I found this entry in the logs Station: f4:34:f0:a3:eb:3d has disassoc by…
-
NWA50AX - Any way to schedule radio on/off daily?
As per title my old ubiquiti had a built in function to turn on/off wifi at specific time of the day. Can this be achieved on the NWA50AX standalone (no nebula)? Thanks
-
NWA55AXE mounting height
Hello, I purchased two NWA55AXE. I wish to connect (wirelessly) two buildings about 65-70 meters apart. There is only one tree that obstructs the direct line of sight. But my questions are:1. Will distance be a problem? 2. On the important question - at what height is it best to mount the two APs? Greetings.
-
How do you disable Client Isolation/AP Isolation checkbox.
How do i disable Client Isolation/AP Isolation checkbox.
