-
WAC5302D Rebooting
Good evening, I have a problem with an AP model WAC5302d-s, which when at least 1-2 stations are connected after about 15-30 min the ap restarts automatically. The AP is managed by controller via a USG-1100 with firmware 4.33 and firmware for the Ap V.5.00. is powered by a GS-1900-48HP switch. As a precaution, I checked…
-
search the firmware 1.00 (WBE.9) for controleur N4100
Hi, I search the firmware 1.00 (WBE.9) for controleur N4100. Find only the WBE.8 on Zyxel Download page. nothing find on the web. would anyone have that? Thanks
-
wifi router zyxel WAH7706 battery is empty.What to do-just recharge?It's not easy!!!
We have bought brand new Zyxel model WAH7706 in Minsk,Belarus 4 days ago. Battery was used 2 h after purchase.TRying to reacharge model during 6 h from attached cable USB-mini USB.No result.Tried to use socket 220V-no result.The battery exhausted totally and don't recharge. Pls help use this equipment for us and recommend…
-
ATP500 & WAC Points Dropping - reason 2 may be the cause?
Hi All, We are running an ATP500 in our office with 2 x WAC6303D-S access points. At random times throughout the day we get no internet over the WiFi and it seems that devices cannot obtain an IP address (even though they've been previously connected a few minutes previously). When looking on the "station info" page on the…
-
NWA1123-ACv2 Command removed error
Hello, I am trying to create 5Ghz wlan radio profile from ssh connection but I keep getting "Command removed due to the platform upgrade." error. I am running following command Router> configure terminal Router(config)# wlan-radio-profile testprofile Router(config-wlan-radio testprofile)# band 5G % Command removed due to…
-
What are the system requirements to install and run Zyxel Access Point Configurator (ZAC)?
What are the system requirements to install and run Zyxel Access Point Configurator (ZAC)?
-
Zyxel WAC - Filesystem /compress full
Hello Our monitoring system reports that the filesytem /compress is full, on a couple of access points. The access points are managed through a NXC2500. What can we do about this, is the filesystem accessible, what is stored on it and can it be cleaned? If so, how can we achieve this? Thanks, best regards, Jaap
-
Layer-2 isolation and subnet problem
Hello, I'm trying to setup a guest wifi with layer-2 isolation on a WAC6103D-I but i can't get it working properly. I have added mac adresses of "VPN GW" and "Internet GW" in my Layer-2 Isolation profile but it still allows users to browse web servers on the main site and internet sites. If i remove VPN GW from my list, i…
-
VPN2S router very slow webui or stuck on login
Hello, I have a VPN2S router and 2 NWA1123 access point. Everithing appears to work well except the login on webui of the router, which is so slow and mayor of cases goes on timeout. Some times works, other I have to refresh the browser a few times, some times appears to be impossible. There are times I'm in and then it…
-
WAC6552D-S - WDS traffic passthrough
Good afternoon all, So, here is what I am trying to do: I want to use the WDS as a LAN extension, not a WiFi extension. AP 1 would be at the main office and then connect to AP 2 at a different building and pass traffic along the wireless bridge. However I cannot find any documentation on how to make this happen. If I set…
-
NWA1123-ACv2 run multiple SSH commands
Hello, I want to run multiple ssh commands with one line on the AP. I tried to separate the commands with a semicolon (;) and && but I keep getting error. You can see the examples down below. $ configure terminal; wlan-security-profile TestSecurityProfile; mode wpa2; wpa-encrypt aes; wpa-psk 12345678; idle 3600; reauth…
-
NXC2500: facing an issue for updating firmware NXC2500_5.40(AAIG.2)C0
We are using NXC2500. Current firmware version is V5.40(AAIG.0). Facing issue while updating firmware to NXC2500_5.40(AAIG.2)C0. Getting error can't update. Also we are facing intermittant error as "AP Disconnect, idle in RUN state" Also all APs disconnecting frequently.. Please help how to resolve
-
AP Firmware - unable to reset the download path to "official"
We've got some problems with regular reboots of our Zyxel AP WAC6103D-I. That's why Zyxel provided us with an interim firmware (v5.40(ABIM.2)) which works so far. For the download we had to change the download path for the capwap firmware. Now we've updated our USG110 to 4.35 (AAPH.2) and would like to change the download…
-
Why are NWA1123-ACv2 trying to connect to various internet-hosts
Hello I noticed that my NWA1123-ACv2 access points are trying to contact various internet-hosts on ports tcp:4335 and tcp:6667, and they do so every 1-3 minutes. At the moment I counted 4 different target IP-adresses which are all in "eu-west-1.compute.amazonaws.com". The access points have a local configuration, not…
-
Suitable AP for production and warehouse facilities
Hi, Sorry if question is posted in wrong place. We are about to establish WiFi coverage in our production (injection molding) and warehouse facilities. I expected to use WAC6502D-E because it seems to have the strongest coverage according to ZyXEL Wireless Optimizer. But that AP seems to have been discontinued. I can't…
-
ZAC doesn't discover NWA1123-ACv2
ZAC version 1.1.2 and NWA1123-ACv2 with firmware V5.00(ABEL.3).I try to discovery with LAN and Wi-Fi but still cannot discovery.Please help me check.
-
Station has deauth. reason 3, event by STA Leave(L2UPFrame). Interface:wlan-1-1: Statio
WLAN_AP1 Zyxel NWA5123-AC_AP1 Boot Module: V2.2 Current Version: V4.30(AAZY.0) Released Date: 2016-07-05 Laufend erfolgen diese Fehlermeldungen. Neue Stationen können nicht angemeldet werden Station has associated. Interface:wlan-1-1: Station: D0:33:11:3B:A7: Station has disassoc. reason 1, event by iwpriv(kickmac).…
-
DHCPV6 Lease Entry - IP format error
When adding a DHCP Lease entry (Configuration->Object->DHCPv6->Lease), I'm unable to add an entry of a local IP address I want to point to for my locally setup DNS server. See screen shot. It won't allow me to enter ANY IP address in the User Defined Address field - and so pulling my hair out trying to figure out what I'm…
-
AP FW v5.40(AAXH.1) - does the AP should reboot regularly?
We are using an AP WAC6103D-I on our USG110 (v4.35(AAPH.0). The AP has the current FW v5.40(AAXH.1) and is connected to a separate USG port in its separate zone. Now it happened that the AP reboots automatically the second time, exactly to the same minute after one week. Is this a normal behaviour of the latest FW that APs…
-
NWA5123-AC HD 3rd Device Low Link Speed - Fixed Bad Cable
Updated. I had a bad cable that was not transmitting at full gig speed. Ok I'm on my third access point and this one is now saying low link speed. I believe it started after updating to latest firmware.
