-
Nebula & 802.11r Roaming Issues
Hello, I have been having some roaming issues which I have narrowed down to 802.11r on some devices, and I thought I'd share this information in the forum. To be honest, I don't know if 802.11r was on by default in Nebula, but I was enabling it assuming I would gain some roaming benefits as per the protocol specifies. With…
-
NXC2500 Access Points randomly reboot
Hello, all APs managed by our NXC2500 randomly reboot throughout the day. I think it might be related to the following issue: [SPR: 1806281062]
[eITS: 180500539]
[Symptom] The managed AP reboot, the alert log shows CAPWAP
AP Disconnect and alert CAPWAP AP SSID stop, it’s related with
smart antenna. We installed version…
-
Guest Access through NWA 1123NI?
How to implement a guest WiFi access with a simple standalone NWA 1123NI? Router is a Draytek 2900, the access point is working flawlessly. Customer wants a guest WiFi, that only talks to the router and prohibits contact to all other devices on the network. Other access points have a simple setting for that, but not the…
-
VLAN end to end walk through
Is there a document that shows me an end - to - end configuration for a secure & guest wireless network on NWA5123-AC, through a GS1920-48HP to a USG310. I have spent days trying to get this to work, and all the instructions show how to do it on the AP, or the switch or the USG but not the whole setup.
-
Difference between NWA1123-AC PRO and WAC6103D-I
Hi everyone What is the difference between those two devices? When comparing the specs everything looks more or less similar. Thanks a lot for any help :) ! #Biz_Nov_2019
-
NWA1123-ACHD repeater mode
Hi all, I bought a set of NWA1123-ACHD devices because I thought I can use them to extend my wifi range. Unfortunately I came to know that those devices are current NOT supporting repeater mode. Question now is: should I sent those back or wait for the repeater mode to come? When is the expected delivery date for this…
-
WAC5302D only 1 radio with 2.4Ghz in a dual radio environment?
Hello I got a mixed setup at one client site with WAC5302-D and NWA5120-AC accesspoints. We got a setup with a profile with 2 radios & 2 SSIDs (WPA2 Security & 2 VLANs). The NWA5120-AC work as expected with WiFi in the 2.4 and 5Ghz frequency. However the WAC5302-D only transmits in the 2.4Ghz band, even though the 2.4Ghz…
-
Guest Voucher
Hello, I'm searching for access points. I already have a USG, so a zyxel access point would fit nice. My problem: we need a guest network with some kind of captive portal and voucher codes for login. Just like for example Ubiquiti is offering it. Has Zyxel something similar in their portfolio? Thanks
-
zyxel nwa1123 ac v2 - setting working time
Hi all,I have installed this AP in my home network and I'm looking for the way to shutdown the AP automatically at a certain hour. In the same way I need to reactivate the AP in the morning. In the user manual I don't find specific instructions or cron command. Could you help me? #Biz_Oct_2019
-
k/v/r support by APs
Hello, I have NXC2500 and 15 access points - 8x NWA5123-AC and 7x NWA5121-N Station info shows that client supports k/v/r in "802.11 features" when connected to NWA5123-AC and N/A when connected to NWA5121-N Is in normal that NWA5121-N by fact don't support k/v/r? Will it change in the future or not? Maybe I am missing…
-
WAC6503d-s antenna
How well will the antenna work in buildings with cement walls?
-
What is the maximum coverage area for WAC6503d-s?
We are planning to use a single WAC6503d-s Access Point (AP) at a small outdoor gathering (about 100 people). The gathering is far from other Wifi networks. What is the maximum coverage area (in either sq ft, radius, or cone) of a single WAC6503d-s? Should we try to put the AP over the gathering, as if it were mounted on a…
-
Enterprise Access Points: Is Shutdown command really mandatory?
We're using Access Points WAC6502D-E, WAC6502D-S, and WAC6503D-S. I just noticed that the users manual says to always use shutdown command, don't just power off, or firmware may become corrupt. See following image of paragraph from manual: Is this really true, or is the risk so slight I don't have to worry about it? Is it…
-
Software
First time setting up a NWA1123-ACv2 and I thought that there was software for local control. I'll probably use the portal but I would like to see the software too. Don't know where to find it. Thank you Kevin
-
How do I repair my bricked Zyxel NWA1100-NH?
I'm not really sure how this happened but it's blinking red without any changes. -M #Biz_WLAN_March
-
Idle in disc state
Hello, i have a NXC2500 controller Fw version v5.40 (aaig.0) and an WAC-6103D Ap actually under this controller i have 11 ap model NWA3160-N perfectly working i can not manage this ap and i don't understand why it's been reconognize by the controller but no way to add in management, i attach the monitor and the logs about…
-
NWA-3560N Managed access point revert to Standalone
Hi, How can I upgrade the firmware of a NWA-3560N, in order to switch operating mode. The AP is in managed mode and I can't access it at all. I need to switch it back to standalone. Since it's running an old firmware, it needs a newer firmware that allows change operating mode. (see…
-
NXC5500 schedule-run only 1 slot
Hi, i am a little bit confused. We have written a script to reboot all APs. Works finde. Fired it up using daily schedule. schedule-run 1 reboot_ap.zysh daily 04:00 Now we want ro run additional scripts. What exactly does "1" mean? schedule-run 2 something_else.zysh daily 05:00 won't work! retval = -1 ERROR: Parse…
-
NWA-1123 ACHD - Web Login via RADIUS/LDAP user
Hi all, the mentioned AP provides the ability to connect to a RADIUS server for Wifi authentication, but it does not provide the same way of authentication for management, why? Is there a specific reason? I am managing my users in an LDAP directory and would like to use that also to allow domain admins access to the AP…
-
NWA-1123 ACHD - Dynamic rate limit assignment via RADIUS
Hi, I am using NWA-1123 ACHD together with a RADIUS server to assign a VLAN based on the user accessing the AP. Unfortunately I have not found any way to dynamically also define a rate limit for this particular user. I know that this can be done SSID-wise, but it would be great to also have this ability user-wise (via some…
